Part Number Hot Search : 
30KP120A SAA1042V TA7303P 1A60A5 EC803 CY7C1353 XBNXX AN1780
Product Description
Full Text Search
 

To Download EP1C12Q240I6ES Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 Section I. Cyclone FPGA Family Data Sheet
This section provides designers with the data sheet specifications for Cyclone(R) devices. The chapters contain feature definitions of the internal architecture, configuration and JTAG boundary-scan testing information, DC operating conditions, AC timing parameters, a reference to power consumption, and ordering information for Cyclone devices. This section contains the following chapters:

Chapter 1. Introduction Chapter 2. Cyclone Architecture Chapter 3. Configuration & Testing Chapter 4. DC & Switching Characteristics Chapter 5. Reference & Ordering Information
Revision History
Refer to each chapter for its own specific revision history. For information on when each chapter was updated, refer to the Chapter Revision Dates section, which appears in the complete handbook.
Altera Corporation
Section I-1 Preliminary
Revision History
Cyclone Device Handbook, Volume 1
Section I-2 Preliminary
Altera Corporation
1. Introduction
C51001-1.4
Introduction
The Cyclone(R) field programmable gate array family is based on a 1.5-V, 0.13-m, all-layer copper SRAM process, with densities up to 20,060 logic elements (LEs) and up to 288 Kbits of RAM. With features like phaselocked loops (PLLs) for clocking and a dedicated double data rate (DDR) interface to meet DDR SDRAM and fast cycle RAM (FCRAM) memory requirements, Cyclone devices are a cost-effective solution for data-path applications. Cyclone devices support various I/O standards, including LVDS at data rates up to 640 megabits per second (Mbps), and 66- and 33-MHz, 64- and 32-bit peripheral component interconnect (PCI), for interfacing with and supporting ASSP and ASIC devices. Altera also offers new low-cost serial configuration devices to configure Cyclone devices. The following shows the main sections in the Cyclone FPGA Family Data Sheet: Section Page
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Logic Array Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Logic Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 MultiTrack Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Embedded Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 Global Clock Network & Phase-Locked Loops. . . . . . . . . . . 2-29 I/O Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39 Power Sequencing & Hot Socketing . . . . . . . . . . . . . . . . . . . . 2-55 IEEE Std. 1149.1 (JTAG) Boundary Scan Support . . . . . . . . . . 3-1 SignalTap II Embedded Logic Analyzer . . . . . . . . . . . . . . . . . 3-5 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Timing Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Device Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Altera Corporation January 2007
1-1 Preliminary
Cyclone Device Handbook, Volume 1
Features
The Cyclone device family offers the following features:

2,910 to 20,060 LEs, see Table 1-1 Up to 294,912 RAM bits (36,864 bytes) Supports configuration through low-cost serial configuration device Support for LVTTL, LVCMOS, SSTL-2, and SSTL-3 I/O standards Support for 66- and 33-MHz, 64- and 32-bit PCI standard High-speed (640 Mbps) LVDS I/O support Low-speed (311 Mbps) LVDS I/O support 311-Mbps RSDS I/O support Up to two PLLs per device provide clock multiplication and phase shifting Up to eight global clock lines with six clock resources available per logic array block (LAB) row Support for external memory, including DDR SDRAM (133 MHz), FCRAM, and single data rate (SDR) SDRAM Support for multiple intellectual property (IP) cores, including Altera(R) MegaCore(R) functions and Altera Megafunctions Partners Program (AMPPSM) megafunctions.
Table 1-1. Cyclone Device Features Feature
LEs M4K RAM blocks (128 x 36 bits) Total RAM bits PLLs Maximum user I/O pins (1) Note to Table 1-1:
(1) This parameter includes global clock pins.
EP1C3
2,910 13 59,904 1 104
EP1C4
4,000 17 78,336 2 301
EP1C6
5,980 20 92,160 2 185
EP1C12
12,060 52 239,616 2 249
EP1C20
20,060 64 294,912 2 301
1-2 Preliminary
Altera Corporation January 2007
Features
Cyclone devices are available in quad flat pack (QFP) and space-saving FineLine(R) BGA packages (see Table 1-2 through 1-3).
Table 1-2. Cyclone Package Options & I/O Pin Counts Device
EP1C3 EP1C4 EP1C6 EP1C12 EP1C20 Notes to Table 1-2:
(1) (2) TQFP: thin quad flat pack. PQFP: plastic quad flat pack. Cyclone devices support vertical migration within the same package (i.e., designers can migrate between the EP1C3 device in the 144-pin TQFP package and the EP1C6 device in the same package)
100-Pin TQFP 144-Pin TQFP 240-Pin PQFP 256-Pin 324-Pin 400-Pin (1) (1), (2) (1) FineLine BGA FineLine BGA FineLine BGA
65 104 249 98 185 173 185 185 249 233 301 301
Vertical migration means you can migrate a design from one device to another that has the same dedicated pins, JTAG pins, and power pins, and are subsets or supersets for a given package across device densities. The largest density in any package has the highest number of power pins; you must use the layout for the largest planned density in a package to provide the necessary power pins for migration. For I/O pin migration across densities, cross-reference the available I/O pins using the device pin-outs for all planned densities of a given package type to identify which I/O pins can be migrated. The Quartus(R) II software can automatically cross-reference and place all pins for you when given a device migration list. If one device has power or ground pins, but these same pins are user I/O on a different device that is in the migration path,the Quartus II software ensures the pins are not used as user I/O in the Quartus II software. Ensure that these pins are connected to the appropriate plane on the board. The Quartus II software reserves I/O pins as power pins as necessary for layout with the larger densities in the same package having more power pins.
Altera Corporation January 2007
1-3 Preliminary
Cyclone Device Handbook, Volume 1
Table 1-3. Cyclone QFP & FineLine BGA Package Sizes Dimension
Pitch (mm) Area (mm2) Length x width (mm x mm)
100-Pin TQFP
0.5 256 16 x 16
144-Pin TQFP
0.5 484 22 x 22
240-Pin PQFP
0.5 1,024 34.6 x 34.6
256-Pin FineLine BGA
1.0 289 17 x 17
324-Pin FineLine BGA
1.0 361 19 x 19
400-Pin FineLine BGA
1.0 441 21 x 21
Document Revision History
Table 1-4 shows the revision history for this document.
Table 1-4. Document Revision History Date & Document Version
January 2007 v1.4 August 2005 v1.3 October 2003 v1.2 September 2003 v1.1 May 2003 v1.0
Changes Made
Added document revision history. Minor updates. Added 64-bit PCI support information.

Summary of Changes
Updated LVDS data rates to 640 Mbps from 311 Mbps. Updated RSDS feature information.
Added document to Cyclone Device Handbook.
1-4 Preliminary
Altera Corporation January 2007
2. Cyclone Architecture
C51002-1.5
Functional Description
Cyclone(R) devices contain a two-dimensional row- and column-based architecture to implement custom logic. Column and row interconnects of varying speeds provide signal interconnects between LABs and embedded memory blocks. The logic array consists of LABs, with 10 LEs in each LAB. An LE is a small unit of logic providing efficient implementation of user logic functions. LABs are grouped into rows and columns across the device. Cyclone devices range between 2,910 to 20,060 LEs. M4K RAM blocks are true dual-port memory blocks with 4K bits of memory plus parity (4,608 bits). These blocks provide dedicated true dual-port, simple dual-port, or single-port memory up to 36-bits wide at up to 250 MHz. These blocks are grouped into columns across the device in between certain LABs. Cyclone devices offer between 60 to 288 Kbits of embedded RAM. Each Cyclone device I/O pin is fed by an I/O element (IOE) located at the ends of LAB rows and columns around the periphery of the device. I/O pins support various single-ended and differential I/O standards, such as the 66- and 33-MHz, 64- and 32-bit PCI standard and the LVDS I/O standard at up to 640 Mbps. Each IOE contains a bidirectional I/O buffer and three registers for registering input, output, and output-enable signals. Dual-purpose DQS, DQ, and DM pins along with delay chains (used to phase-align DDR signals) provide interface support with external memory devices such as DDR SDRAM, and FCRAM devices at up to 133 MHz (266 Mbps). Cyclone devices provide a global clock network and up to two PLLs. The global clock network consists of eight global clock lines that drive throughout the entire device. The global clock network can provide clocks for all resources within the device, such as IOEs, LEs, and memory blocks. The global clock lines can also be used for control signals. Cyclone PLLs provide general-purpose clocking with clock multiplication and phase shifting as well as external outputs for high-speed differential I/O support. Figure 2-1 shows a diagram of the Cyclone EP1C12 device.
Altera Corporation January 2007
2-1 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-1. Cyclone EP1C12 Device Block Diagram
IOEs
Logic Array
PLL
EP1C12 Device
M4K Blocks
The number of M4K RAM blocks, PLLs, rows, and columns vary per device. Table 2-1 lists the resources available in each Cyclone device.
Table 2-1. Cyclone Device Resources M4K RAM Device Columns
EP1C3 EP1C4 EP1C6 EP1C12 EP1C20 1 1 1 2 2
PLLs Blocks
13 17 20 52 64 1 2 2 2 2
LAB Columns
24 26 32 48 64
LAB Rows
13 17 20 26 32
2-2 Preliminary
Altera Corporation January 2007
Logic Array Blocks
Logic Array Blocks
Each LAB consists of 10 LEs, LE carry chains, LAB control signals, a local interconnect, look-up table (LUT) chain, and register chain connection lines. The local interconnect transfers signals between LEs in the same LAB. LUT chain connections transfer the output of one LE's LUT to the adjacent LE for fast sequential LUT connections within the same LAB. Register chain connections transfer the output of one LE's register to the adjacent LE's register within an LAB. The Quartus(R) II Compiler places associated logic within an LAB or adjacent LABs, allowing the use of local, LUT chain, and register chain connections for performance and area efficiency. Figure 2-2 details the Cyclone LAB.
Figure 2-2. Cyclone LAB Structure
Row Interconnect
Column Interconnect
Direct link interconnect from adjacent block
Direct link interconnect from adjacent block
Direct link interconnect to adjacent block
Direct link interconnect to adjacent block
LAB
Local Interconnect
LAB Interconnects
The LAB local interconnect can drive LEs within the same LAB. The LAB local interconnect is driven by column and row interconnects and LE outputs within the same LAB. Neighboring LABs, PLLs, and M4K RAM blocks from the left and right can also drive an LAB's local interconnect through the direct link connection. The direct link connection feature minimizes the use of row and column interconnects, providing higher
Altera Corporation January 2007
2-3 Preliminary
Cyclone Device Handbook, Volume 1
performance and flexibility. Each LE can drive 30 other LEs through fast local and direct link interconnects. Figure 2-3 shows the direct link connection. Figure 2-3. Direct Link Connection
Direct link interconnect from left LAB, M4K memory block, PLL, or IOE output Direct link interconnect from right LAB, M4K memory block, PLL, or IOE output
Direct link interconnect to left Local Interconnect LAB
Direct link interconnect to right
LAB Control Signals
Each LAB contains dedicated logic for driving control signals to its LEs. The control signals include two clocks, two clock enables, two asynchronous clears, synchronous clear, asynchronous preset/load, synchronous load, and add/subtract control signals. This gives a maximum of 10 control signals at a time. Although synchronous load and clear signals are generally used when implementing counters, they can also be used with other functions. Each LAB can use two clocks and two clock enable signals. Each LAB's clock and clock enable signals are linked. For example, any LE in a particular LAB using the labclk1 signal will also use labclkena1. If the LAB uses both the rising and falling edges of a clock, it also uses both LAB-wide clock signals. De-asserting the clock enable signal will turn off the LAB-wide clock. Each LAB can use two asynchronous clear signals and an asynchronous load/preset signal. The asynchronous load acts as a preset when the asynchronous load data input is tied high.
2-4 Preliminary
Altera Corporation January 2007
Logic Elements
With the LAB-wide addnsub control signal, a single LE can implement a one-bit adder and subtractor. This saves LE resources and improves performance for logic functions such as DSP correlators and signed multipliers that alternate between addition and subtraction depending on data. The LAB row clocks [5..0] and LAB local interconnect generate the LABwide control signals. The MultiTrackTM interconnect's inherent low skew allows clock and control signal distribution in addition to data. Figure 2-4 shows the LAB control signal generation circuit. Figure 2-4. LAB-Wide Control Signals
Dedicated LAB Row Clocks Local Interconnect Local Interconnect 6
Local Interconnect Local Interconnect Local Interconnect Local Interconnect labclk1
labclkena1
labclkena2
syncload
labclr2
addnsub
labclk2
asyncload or labpre
labclr1
synclr
Logic Elements
The smallest unit of logic in the Cyclone architecture, the LE, is compact and provides advanced features with efficient logic utilization. Each LE contains a four-input LUT, which is a function generator that can implement any function of four variables. In addition, each LE contains a programmable register and carry chain with carry select capability. A single LE also supports dynamic single bit addition or subtraction mode selectable by an LAB-wide control signal. Each LE drives all types of interconnects: local, row, column, LUT chain, register chain, and direct link interconnects. See Figure 2-5.
Altera Corporation January 2007
2-5 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-5. Cyclone LE
Register chain routing from previous LE LAB-wide Register Bypass Synchronous Load LAB-wide Packed Synchronous Register Select Clear
LAB Carry-In addnsub Carry-In1 Carry-In0
Programmable Register LUT chain routing to next LE Row, column, and direct link routing
data1 data2 data3 data4
ENA CLRN
Look-Up Table (LUT)
Carry Chain
Synchronous Load and Clear Logic
PRN/ALD D Q ADATA
Row, column, and direct link routing
labclr1 labclr2 labpre/aload Chip-Wide Reset
Asynchronous Clear/Preset/ Load Logic
Local Routing
Clock & Clock Enable Select labclk1 labclk2 labclkena1 labclkena2
Register Feedback
Register chain output
Carry-Out0 Carry-Out1 LAB Carry-Out
Each LE's programmable register can be configured for D, T, JK, or SR operation. Each register has data, true asynchronous load data, clock, clock enable, clear, and asynchronous load/preset inputs. Global signals, general-purpose I/O pins, or any internal logic can drive the register's clock and clear control signals. Either general-purpose I/O pins or internal logic can drive the clock enable, preset, asynchronous load, and asynchronous data. The asynchronous load data input comes from the data3 input of the LE. For combinatorial functions, the LUT output bypasses the register and drives directly to the LE outputs. Each LE has three outputs that drive the local, row, and column routing resources. The LUT or register output can drive these three outputs independently. Two LE outputs drive column or row and direct link routing connections and one drives local interconnect resources. This allows the LUT to drive one output while the register drives another output. This feature, called register packing, improves device utilization because the device can use the register and the LUT for unrelated
2-6 Preliminary
Altera Corporation January 2007
Logic Elements
functions. Another special packing mode allows the register output to feed back into the LUT of the same LE so that the register is packed with its own fan-out LUT. This provides another mechanism for improved fitting. The LE can also drive out registered and unregistered versions of the LUT output.
LUT Chain & Register Chain
In addition to the three general routing outputs, the LEs within an LAB have LUT chain and register chain outputs. LUT chain connections allow LUTs within the same LAB to cascade together for wide input functions. Register chain outputs allow registers within the same LAB to cascade together. The register chain output allows an LAB to use LUTs for a single combinatorial function and the registers to be used for an unrelated shift register implementation. These resources speed up connections between LABs while saving local interconnect resources. "MultiTrack Interconnect" on page 2-12 for more information on LUT chain and register chain connections.
addnsub Signal
The LE's dynamic adder/subtractor feature saves logic resources by using one set of LEs to implement both an adder and a subtractor. This feature is controlled by the LAB-wide control signal addnsub. The addnsub signal sets the LAB to perform either A + B or A -B. The LUT computes addition; subtraction is computed by adding the two's complement of the intended subtractor. The LAB-wide signal converts to two's complement by inverting the B bits within the LAB and setting carry-in = 1 to add one to the least significant bit (LSB). The LSB of an adder/subtractor must be placed in the first LE of the LAB, where the LAB-wide addnsub signal automatically sets the carry-in to 1. The Quartus II Compiler automatically places and uses the adder/subtractor feature when using adder/subtractor parameterized functions.
LE Operating Modes
The Cyclone LE can operate in one of the following modes:

Normal mode Dynamic arithmetic mode
Each mode uses LE resources differently. In each mode, eight available inputs to the LE four data inputs from the LAB local interconnect, the carry-in0 and carry-in1 from the previous LE, the LAB carry-in from the previous carry-chain LAB, and the register chain connection are directed to different destinations to implement the desired logic function. LAB-wide signals provide clock, asynchronous clear, asynchronous
Altera Corporation January 2007
2-7 Preliminary
Cyclone Device Handbook, Volume 1
preset/load, synchronous clear, synchronous load, and clock enable control for the register. These LAB-wide signals are available in all LE modes. The addnsub control signal is allowed in arithmetic mode. The Quartus II software, in conjunction with parameterized functions such as library of parameterized modules (LPM) functions, automatically chooses the appropriate mode for common functions such as counters, adders, subtractors, and arithmetic functions. If required, you can also create special-purpose functions that specify which LE operating mode to use for optimal performance.
Normal Mode
The normal mode is suitable for general logic applications and combinatorial functions. In normal mode, four data inputs from the LAB local interconnect are inputs to a four-input LUT (see Figure 2-6). The Quartus II Compiler automatically selects the carry-in or the data3 signal as one of the inputs to the LUT. Each LE can use LUT chain connections to drive its combinatorial output directly to the next LE in the LAB. Asynchronous load data for the register comes from the data3 input of the LE. LEs in normal mode support packed registers. Figure 2-6. LE in Normal Mode
sload sclear (LAB Wide) (LAB Wide) Register chain connection aload (LAB Wide)
addnsub (LAB Wide)
(1)
data1 data2 data3 cin (from cout of previous LE) data4
4-Input LUT
ALD/PRE ADATA Q D ENA CLRN
Row, column, and direct link routing Row, column, and direct link routing
clock (LAB Wide) ena (LAB Wide) aclr (LAB Wide)
Local routing
LUT chain connection Register chain output
Register Feedback
Note to Figure 2-6:
(1) This signal is only allowed in normal mode if the LE is at the end of an adder/subtractor chain.
2-8 Preliminary
Altera Corporation January 2007
Logic Elements
Dynamic Arithmetic Mode
The dynamic arithmetic mode is ideal for implementing adders, counters, accumulators, wide parity functions, and comparators. An LE in dynamic arithmetic mode uses four 2-input LUTs configurable as a dynamic adder/subtractor. The first two 2-input LUTs compute two summations based on a possible carry-in of 1 or 0; the other two LUTs generate carry outputs for the two chains of the carry select circuitry. As shown in Figure 2-7, the LAB carry-in signal selects either the carry-in0 or carry-in1 chain. The selected chain's logic level in turn determines which parallel sum is generated as a combinatorial or registered output. For example, when implementing an adder, the sum output is the selection of two possible calculated sums: data1 + data2 + carry-in0 or data1 + data2 + carry-in1 The other two LUTs use the data1 and data2 signals to generate two possible carry-out signals for a carry of 1 and the other for a carry of one 0. The carry-in0 signal acts as the carry select for the carry-out0 output and carry-in1 acts as the carry select for the carry-out1 output. LEs in arithmetic mode can drive out registered and unregistered versions of the LUT output. The dynamic arithmetic mode also offers clock enable, counter enable, synchronous up/down control, synchronous clear, synchronous load, and dynamic adder/subtractor options. The LAB local interconnect data inputs generate the counter enable and synchronous up/down control signals. The synchronous clear and synchronous load options are LABwide signals that affect all registers in the LAB. The Quartus II software automatically places any registers that are not used by the counter into other LABs. The addnsub LAB-wide signal controls whether the LE acts as an adder or subtractor.
Altera Corporation January 2007
2-9 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-7. LE in Dynamic Arithmetic Mode
LAB Carry-In Carry-In0 Carry-In1 addnsub (LAB Wide) (1) sload sclear (LAB Wide) (LAB Wide) Register chain connection aload (LAB Wide)
data1 data2 data3
LUT
ALD/PRE ADATA Q D ENA CLRN
Row, column, and direct link routing Row, column, and direct link routing
LUT
LUT
clock (LAB Wide) ena (LAB Wide) aclr (LAB Wide)
Local routing
LUT
LUT chain connection Register chain output Register Feedback
Carry-Out0 Carry-Out1
Note to Figure 2-7:
(1) The addnsub signal is tied to the carry input for the first LE of a carry chain only.
Carry-Select Chain
The carry-select chain provides a very fast carry-select function between LEs in dynamic arithmetic mode. The carry-select chain uses the redundant carry calculation to increase the speed of carry functions. The LE is configured to calculate outputs for a possible carry-in of 0 and carryin of 1 in parallel. The carry-in0 and carry-in1 signals from a lowerorder bit feed forward into the higher-order bit via the parallel carry chain and feed into both the LUT and the next portion of the carry chain. Carryselect chains can begin in any LE within an LAB. The speed advantage of the carry-select chain is in the parallel precomputation of carry chains. Since the LAB carry-in selects the precomputed carry chain, not every LE is in the critical path. Only the propagation delays between LAB carry-in generation (LE 5 and LE 10) are now part of the critical path. This feature allows the Cyclone architecture to implement high-speed counters, adders, multipliers, parity functions, and comparators of arbitrary width.
2-10 Preliminary
Altera Corporation January 2007
Logic Elements
Figure 2-8 shows the carry-select circuitry in an LAB for a 10-bit full adder. One portion of the LUT generates the sum of two bits using the input signals and the appropriate carry-in bit; the sum is routed to the output of the LE. The register can be bypassed for simple adders or used for accumulator functions. Another portion of the LUT generates carryout bits. An LAB-wide carry-in bit selects which chain is used for the addition of given inputs. The carry-in signal for each chain, carry-in0 or carry-in1, selects the carry-out to carry forward to the carry-in signal of the next-higher-order bit. The final carry-out signal is routed to an LE, where it is fed to local, row, or column interconnects. Figure 2-8. Carry Select Chain
LAB Carry-In A1 B1 A2 B2
0 LE1
1 Sum1
LAB Carry-In Carry-In0 Carry-In1
LE2
Sum2
LUT data1 data2 Sum LUT
A3 B3 A4 B4
LE3
Sum3
LE4
Sum4
LUT
A5 B5
LE5
Sum5
LUT
0 A6 B6 A7 B7 A8 B8 A9 B9 A10 B10 LE6
1 Sum6
Carry-Out0
Carry-Out1
LE7
Sum7
LE8
Sum8
LE9
Sum9
LE10
Sum10
LAB Carry-Out
Altera Corporation January 2007
2-11 Preliminary
Cyclone Device Handbook, Volume 1
The Quartus II Compiler automatically creates carry chain logic during design processing, or you can create it manually during design entry. Parameterized functions such as LPM functions automatically take advantage of carry chains for the appropriate functions. The Quartus II Compiler creates carry chains longer than 10 LEs by linking LABs together automatically. For enhanced fitting, a long carry chain runs vertically allowing fast horizontal connections to M4K memory blocks. A carry chain can continue as far as a full column.
Clear & Preset Logic Control
LAB-wide signals control the logic for the register's clear and preset signals. The LE directly supports an asynchronous clear and preset function. The register preset is achieved through the asynchronous load of a logic high. The direct asynchronous preset does not require a NOTgate push-back technique. Cyclone devices support simultaneous preset/ asynchronous load and clear signals. An asynchronous clear signal takes precedence if both signals are asserted simultaneously. Each LAB supports up to two clears and one preset signal. In addition to the clear and preset ports, Cyclone devices provide a chipwide reset pin (DEV_CLRn) that resets all registers in the device. An option set before compilation in the Quartus II software controls this pin. This chip-wide reset overrides all other control signals.
MultiTrack Interconnect
In the Cyclone architecture, connections between LEs, M4K memory blocks, and device I/O pins are provided by the MultiTrack interconnect structure with DirectDriveTM technology. The MultiTrack interconnect consists of continuous, performance-optimized routing lines of different speeds used for inter- and intra-design block connectivity. The Quartus II Compiler automatically places critical design paths on faster interconnects to improve design performance. DirectDrive technology is a deterministic routing technology that ensures identical routing resource usage for any function regardless of placement within the device. The MultiTrack interconnect and DirectDrive technology simplify the integration stage of block-based designing by eliminating the re-optimization cycles that typically follow design changes and additions. The MultiTrack interconnect consists of row and column interconnects that span fixed distances. A routing structure with fixed length resources for all devices allows predictable and repeatable performance when
2-12 Preliminary
Altera Corporation January 2007
MultiTrack Interconnect
migrating through different device densities. Dedicated row interconnects route signals to and from LABs, PLLs, and M4K memory blocks within the same row. These row resources include:

Direct link interconnects between LABs and adjacent blocks R4 interconnects traversing four blocks to the right or left
The direct link interconnect allows an LAB or M4K memory block to drive into the local interconnect of its left and right neighbors. Only one side of a PLL block interfaces with direct link and row interconnects. The direct link interconnect provides fast communication between adjacent LABs and/or blocks without using row interconnect resources. The R4 interconnects span four LABs, or two LABs and one M4K RAM block. These resources are used for fast row connections in a four-LAB region. Every LAB has its own set of R4 interconnects to drive either left or right. Figure 2-9 shows R4 interconnect connections from an LAB. R4 interconnects can drive and be driven by M4K memory blocks, PLLs, and row IOEs. For LAB interfacing, a primary LAB or LAB neighbor can drive a given R4 interconnect. For R4 interconnects that drive to the right, the primary LAB and right neighbor can drive on to the interconnect. For R4 interconnects that drive to the left, the primary LAB and its left neighbor can drive on to the interconnect. R4 interconnects can drive other R4 interconnects to extend the range of LABs they can drive. R4 interconnects can also drive C4 interconnects for connections from one row to another.
Altera Corporation January 2007
2-13 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-9. R4 Interconnect Connections
Adjacent LAB can Drive onto Another LAB's R4 Interconnect R4 Interconnect Driving Left C4 Column Interconnects (1) R4 Interconnect Driving Right
LAB Neighbor
Primary LAB (2)
LAB Neighbor
Notes to Figure 2-9:
(1) (2) C4 interconnects can drive R4 interconnects. This pattern is repeated for every LAB in the LAB row.
The column interconnect operates similarly to the row interconnect. Each column of LABs is served by a dedicated column interconnect, which vertically routes signals to and from LABs, M4K memory blocks, and row and column IOEs. These column resources include:

LUT chain interconnects within an LAB Register chain interconnects within an LAB C4 interconnects traversing a distance of four blocks in an up and down direction
Cyclone devices include an enhanced interconnect structure within LABs for routing LE output to LE input connections faster using LUT chain connections and register chain connections. The LUT chain connection allows the combinatorial output of an LE to directly drive the fast input of the LE right below it, bypassing the local interconnect. These resources can be used as a high-speed connection for wide fan-in functions from LE 1 to LE 10 in the same LAB. The register chain connection allows the register output of one LE to connect directly to the register input of the next LE in the LAB for fast shift registers. The Quartus II Compiler automatically takes advantage of these resources to improve utilization and performance. Figure 2-10 shows the LUT chain and register chain interconnects.
2-14 Preliminary
Altera Corporation January 2007
MultiTrack Interconnect
Figure 2-10. LUT Chain & Register Chain Interconnects
Local Interconnect Routing Among LEs in the LAB LUT Chain Routing to Adjacent LE LE 1
Register Chain Routing to Adjacent LE's Register Input
LE 2 Local Interconnect LE 3 LE 4 LE 5 LE 6
LE 7 LE 8 LE 9
LE 10
The C4 interconnects span four LABs or M4K blocks up or down from a source LAB. Every LAB has its own set of C4 interconnects to drive either up or down. Figure 2-11 shows the C4 interconnect connections from an LAB in a column. The C4 interconnects can drive and be driven by all types of architecture blocks, including PLLs, M4K memory blocks, and column and row IOEs. For LAB interconnection, a primary LAB or its LAB neighbor can drive a given C4 interconnect. C4 interconnects can drive each other to extend their range as well as drive row interconnects for column-to-column connections.
Altera Corporation January 2007
2-15 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-11. C4 Interconnect Connections
Note (1)
C4 Interconnect Drives Local and R4 Interconnects Up to Four Rows
C4 Interconnect Driving Up
LAB
Row Interconnect
Adjacent LAB can drive onto neighboring LAB's C4 interconnect
Local Interconnect
C4 Interconnect Driving Down
Note to Figure 2-11:
(1) Each C4 interconnect can drive either up or down four rows.
2-16 Preliminary
Altera Corporation January 2007
MultiTrack Interconnect
All embedded blocks communicate with the logic array similar to LABto-LAB interfaces. Each block (i.e., M4K memory or PLL) connects to row and column interconnects and has local interconnect regions driven by row and column interconnects. These blocks also have direct link interconnects for fast connections to and from a neighboring LAB. Table 2-2 shows the Cyclone device's routing scheme.
Table 2-2. Cyclone Device Routing Scheme Destination Direct Link Interconnect
Local Interconnect
Register Chain
Source LUT Chain
M4K RAM Block
R4 Interconnect
C4 Interconnect
Column IOE v
LUT Chain Register Chain Local Interconnect Direct Link Interconnect R4 Interconnect C4 Interconnect LE M4K RAM Block PLL Column IOE Row IOE
v v v v v v v v v v v v v v v v v v v v v v v v v v v v v v
Altera Corporation January 2007
2-17 Preliminary
Row IOE
PLL
LE
Cyclone Device Handbook, Volume 1
Embedded Memory
The Cyclone embedded memory consists of columns of M4K memory blocks. EP1C3 and EP1C6 devices have one column of M4K blocks, while EP1C12 and EP1C20 devices have two columns (see Table 1-1 on page 1-2 for total RAM bits per density). Each M4K block can implement various types of memory with or without parity, including true dual-port, simple dual-port, and single-port RAM, ROM, and FIFO buffers. The M4K blocks support the following features:

4,608 RAM bits 250 MHz performance True dual-port memory Simple dual-port memory Single-port memory Byte enable Parity bits Shift register FIFO buffer ROM Mixed clock mode
Violating the setup or hold time on the address registers could corrupt the memory contents. This applies to both read and write operations.
1
Memory Modes
The M4K memory blocks include input registers that synchronize writes and output registers to pipeline designs and improve system performance. M4K blocks offer a true dual-port mode to support any combination of two-port operations: two reads, two writes, or one read and one write at two different clock frequencies. Figure 2-12 shows true dual-port memory. Figure 2-12. True Dual-Port Memory Configuration
A dataA[ ] addressA[ ] wrenA clockA clockenA qA[ ] aclrA B dataB[ ] addressB[ ] wrenB clockB clockenB qB[ ] aclrB
2-18 Preliminary
Altera Corporation January 2007
Embedded Memory
In addition to true dual-port memory, the M4K memory blocks support simple dual-port and single-port RAM. Simple dual-port memory supports a simultaneous read and write. Single-port memory supports non-simultaneous reads and writes. Figure 2-13 shows these different M4K RAM memory port configurations. Figure 2-13. Simple Dual-Port & Single-Port Memory Configurations
Simple Dual-Port Memory
data[ ] wraddress[ ] wren inclock inclocken inaclr rdaddress[ ] rden q[ ] outclock outclocken outaclr
Single-Port Memory (1)
data[ ] address[ ] wren inclock inclocken inaclr
q[ ] outclock outclocken outaclr
Note to Figure 2-13:
(1) Two single-port memory blocks can be implemented in a single M4K block as long as each of the two independent block sizes is equal to or less than half of the M4K block size.
The memory blocks also enable mixed-width data ports for reading and writing to the RAM ports in dual-port RAM configuration. For example, the memory block can be written in x1 mode at port A and read out in x16 mode from port B. The Cyclone memory architecture can implement fully synchronous RAM by registering both the input and output signals to the M4K RAM block. All M4K memory block inputs are registered, providing synchronous write cycles. In synchronous operation, the memory block generates its own self-timed strobe write enable (wren) signal derived from a global clock. In contrast, a circuit using asynchronous RAM must generate the RAM wren signal while ensuring its data and address signals meet setup and hold time specifications relative to the wren
Altera Corporation January 2007
2-19 Preliminary
Cyclone Device Handbook, Volume 1
signal. The output registers can be bypassed. Pseudo-asynchronous reading is possible in the simple dual-port mode of M4K blocks by clocking the read enable and read address registers on the negative clock edge and bypassing the output registers. When configured as RAM or ROM, you can use an initialization file to pre-load the memory contents. Two single-port memory blocks can be implemented in a single M4K block as long as each of the two independent block sizes is equal to or less than half of the M4K block size. The Quartus II software automatically implements larger memory by combining multiple M4K memory blocks. For example, two 256x16-bit RAM blocks can be combined to form a 256x32-bit RAM block. Memory performance does not degrade for memory blocks using the maximum number of words allowed. Logical memory blocks using less than the maximum number of words use physical blocks in parallel, eliminating any external control logic that would increase delays. To create a larger high-speed memory block, the Quartus II software automatically combines memory blocks with LE control logic.
Parity Bit Support
The M4K blocks support a parity bit for each byte. The parity bit, along with internal LE logic, can implement parity checking for error detection to ensure data integrity. You can also use parity-size data words to store user-specified control bits. Byte enables are also available for data input masking during write operations.
Shift Register Support
You can configure M4K memory blocks to implement shift registers for DSP applications such as pseudo-random number generators, multichannel filtering, auto-correlation, and cross-correlation functions. These and other DSP applications require local data storage, traditionally implemented with standard flip-flops, which can quickly consume many logic cells and routing resources for large shift registers. A more efficient alternative is to use embedded memory as a shift register block, which saves logic cell and routing resources and provides a more efficient implementation with the dedicated circuitry. The size of a w x m x n shift register is determined by the input data width (w), the length of the taps (m), and the number of taps (n). The size of a w x m x n shift register must be less than or equal to the maximum number of memory bits in the M4K block (4,608 bits). The total number of shift
2-20 Preliminary
Altera Corporation January 2007
Embedded Memory
register outputs (number of taps n x width w) must be less than the maximum data width of the M4K RAM block (x36). To create larger shift registers, multiple memory blocks are cascaded together. Data is written into each address location at the falling edge of the clock and read from the address at the rising edge of the clock. The shift register mode logic automatically controls the positive and negative edge clocking to shift the data in one clock cycle. Figure 2-14 shows the M4K memory block in the shift register mode. Figure 2-14. Shift Register Memory Configuration
w x m x n Shift Register m-Bit Shift Register w w
m-Bit Shift Register w w
n Number of Taps
m-Bit Shift Register w w
m-Bit Shift Register w w
Memory Configuration Sizes
The memory address depths and output widths can be configured as 4,096 x 1, 2,048 x 2, 1,024 x 4, 512 x 8 (or 512 x 9 bits), 256 x 16 (or 256 x 18 bits), and 128 x 32 (or 128 x 36 bits). The 128 x 32- or 36-bit configuration
Altera Corporation January 2007
2-21 Preliminary
Cyclone Device Handbook, Volume 1
is not available in the true dual-port mode. Mixed-width configurations are also possible, allowing different read and write widths. Tables 2-3 and 2-4 summarize the possible M4K RAM block configurations.
Table 2-3. M4K RAM Block Configurations (Simple Dual-Port) Write Port Read Port 4K x 1
4K x 1 2K x 2 1K x 4 512 x 8 256 x 16 128 x 32 512 x 9 256 x 18 128 x 36
2K x 2 v v v v v v
1K x 4 v v v v v v
512 x 8 v v v v v v
256 x 16 v v v v v v
128 x 32 v v v v v v
512 x 9 256 x 18 128 x 36
v v v v v v
v v v
v v v
v v v
Table 2-4. M4K RAM Block Configurations (True Dual-Port) Port B Port A 4K x 1
4K x 1 2K x 2 1K x 4 512 x 8 256 x 16 512 x 9 256 x 18
2K x 2 v v v v v
1K x 4 v v v v v
512 x 8 v v v v v
256 x 16 v v v v v
512 x 9
256 x 18
v v v v v
v v
v v
When the M4K RAM block is configured as a shift register block, you can create a shift register up to 4,608 bits (w x m x n).
2-22 Preliminary
Altera Corporation January 2007
Embedded Memory
Byte Enables
M4K blocks support byte writes when the write port has a data width of 16, 18, 32, or 36 bits. The byte enables allow the input data to be masked so the device can write to specific bytes. The unwritten bytes retain the previous written value. Table 2-5 summarizes the byte selection.
Table 2-5. Byte Enable for M4K Blocks byteena[3..0]
[0] = 1 [1] = 1 [2] = 1 [3] = 1 Notes to Table 2-5:
(1) (2)
Notes (1), (2) datain x 36
[8..0] [17..9] [26..18] [35..27]
datain x 18
[8..0] [17..9] - -
Any combination of byte enables is possible. Byte enables can be used in the same manner with 8-bit words, i.e., in x 16 and x 32 modes.
Control Signals & M4K Interface
The M4K blocks allow for different clocks on their inputs and outputs. Either of the two clocks feeding the block can clock M4K block registers (renwe, address, byte enable, datain, and output registers). Only the output register can be bypassed. The six labclk signals or local interconnects can drive the control signals for the A and B ports of the M4K block. LEs can also control the clock_a, clock_b, renwe_a, renwe_b, clr_a, clr_b, clocken_a, and clocken_b signals, as shown in Figure 2-15. The R4, C4, and direct link interconnects from adjacent LABs drive the M4K block local interconnect. The M4K blocks can communicate with LABs on either the left or right side through these row resources or with LAB columns on either the right or left with the column resources. Up to 10 direct link input connections to the M4K block are possible from the left adjacent LABs and another 10 possible from the right adjacent LAB. M4K block outputs can also connect to left and right LABs through 10 direct link interconnects each. Figure 2-16 shows the M4K block to logic array interface.
Altera Corporation January 2007
2-23 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-15. M4K RAM Block Control Signals
Dedicated LAB Row Clocks Local Interconnect 6
Local Interconnect
Local Interconnect Local Interconnect Local Interconnect clocken_a Local Interconnect clock_a renwe_a alcr_b clocken_b alcr_a renwe_b clock_b
Local Interconnect Local Interconnect Local Interconnect Local Interconnect
Figure 2-16. M4K RAM Block LAB Row Interface
C4 Interconnects R4 Interconnects
Direct link interconnect to adjacent LAB
10
Direct link interconnect to adjacent LAB dataout
Direct link interconnect from adjacent LAB
M4K RAM Block Byte enable Control Signals Clocks
Direct link interconnect from adjacent LAB
address
datain
6 M4K RAM Block Local Interconnect Region LAB Row Clocks
2-24 Preliminary
Altera Corporation January 2007
Embedded Memory
Independent Clock Mode
The M4K memory blocks implement independent clock mode for true dual-port memory. In this mode, a separate clock is available for each port (ports A and B). Clock A controls all registers on the port A side, while clock B controls all registers on the port B side. Each port, A and B, also supports independent clock enables and asynchronous clear signals for port A and B registers. Figure 2-17 shows an M4K memory block in independent clock mode. Figure 2-17. Independent Clock Mode
6 LAB Row Clocks
Notes (1), (2)
A 6 dataA[ ]
D ENA Q
Data In
Memory Block 256 16 (2) 512 8 1,024 4 2,048 2 4,096 1
B 6 Data In
Q D ENA
dataB[ ]
byteenaA[ ]
D ENA
Q
Byte Enable A
Byte Enable B
Q
D ENA
byteenaB[ ]
addressA[ ]
D ENA
Q
Address A
Address B
Q
D ENA
addressB[ ]
wrenA
wrenB Write/Read Enable
clkenA clockA
D ENA
Q
Write Pulse Generator
Write/Read Enable
Write Pulse Generator
Q
D ENA
clkenB clockB
Data Out
Data Out
D ENA
Q
Q
D ENA
qA[ ]
qB[ ]
Notes to Figure 2-17:
(1) (2) All registers shown have asynchronous clear ports. Violating the setup or hold time on the address registers could corrupt the memory contents. This applies to both read and write operations.
Input/Output Clock Mode
Input/output clock mode can be implemented for both the true and simple dual-port memory modes. On each of the two ports, A or B, one clock controls all registers for inputs into the memory block: data input, wren, and address. The other clock controls the block's data output registers. Each memory block port, A or B, also supports independent clock enables and asynchronous clear signals for input and output registers. Figures 2-18 and 2-19 show the memory block in input/output clock mode.
Altera Corporation January 2007
2-25 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-18. Input/Output Clock Mode in True Dual-Port Mode
6 LAB Row Clocks 6 dataA[ ]
D ENA Q
Note (1), (2)
A Data In
Memory Block 256 x 16 (2) 512 x 8 1,024 x 4 2,048 x 2 4,096 x 1
B Data In
Q D ENA
6 dataB[ ]
byteenaA[ ]
D ENA
Q
Byte Enable A
Byte Enable B
Q
D ENA
byteenaB[ ]
addressA[ ]
D ENA
Q
Address A
Address B
Q
D ENA
addressB[ ]
wrenA wrenB clkenA clockA
D ENA Q
Write Pulse Generator
Write/Read Enable
Write/Read Enable
Write Pulse Generator
Q
D ENA
Data Out
Data Out
clkenB
D ENA Q Q D ENA
clockB
q A[ ]
qB[ ]
Notes to Figure 2-18:
(1) (2) All registers shown have asynchronous clear ports. Violating the setup or hold time on the address registers could corrupt the memory contents. This applies to both read and write operations.
2-26 Preliminary
Altera Corporation January 2007
Embedded Memory
Figure 2-19. Input/Output Clock Mode in Simple Dual-Port Mode
6 LAB Row Clocks 6 data[ ] D Q ENA
Notes (1), (2)
Memory Block 256 16 Data In 512 8 1,024 4 2,048 2 4,096 1 Read Address
address[ ]
D Q ENA
Data Out byteena[ ] D Q ENA Byte Enable
D Q ENA
To MultiTrack Interconnect
wraddress[ ]
D Q ENA
Write Address
rden D Q ENA wren Read Enable
outclken
inclken inclock
D Q ENA
Write Pulse Generator
Write Enable
outclock
Notes to Figure 2-19:
(1) (2) All registers shown except the rden register have asynchronous clear ports. Violating the setup or hold time on the address registers could corrupt the memory contents. This applies to both read and write operations.
Altera Corporation January 2007
2-27 Preliminary
Cyclone Device Handbook, Volume 1
Read/Write Clock Mode
The M4K memory blocks implement read/write clock mode for simple dual-port memory. You can use up to two clocks in this mode. The write clock controls the block's data inputs, wraddress, and wren. The read clock controls the data output, rdaddress, and rden. The memory blocks support independent clock enables for each clock and asynchronous clear signals for the read- and write-side registers. Figure 2-20 shows a memory block in read/write clock mode. Figure 2-20. Read/Write Clock Mode in Simple Dual-Port Mode
6 LAB Row Clocks 6 data[ ] D Q ENA
Notes (1), (2)
Memory Block 256 x 16 512 x 8 1,024 x 4 Data In 2,048 x 2 4,096 x 1 Data Out D Q ENA To MultiTrack Interconnect
address[ ]
D Q ENA
Read Address
wraddress[ ]
D Q ENA
Write Address
byteena[ ]
D Q ENA
Byte Enable
rden D Q ENA wren Read Enable
rdclken
wrclken wrclock
D Q ENA
Write Pulse Generator
Write Enable
rdclock
Notes to Figure 2-20:
(1) (2) All registers shown except the rden register have asynchronous clear ports. Violating the setup or hold time on the address registers could corrupt the memory contents. This applies to both read and write operations.
2-28 Preliminary
Altera Corporation January 2007
Global Clock Network & Phase-Locked Loops
Single-Port Mode
The M4K memory blocks also support single-port mode, used when simultaneous reads and writes are not required. See Figure 2-21. A single M4K memory block can support up to two single-port mode RAM blocks if each RAM block is less than or equal to 2K bits in size. Figure 2-21. Single-Port Mode
6 LAB Row Clocks
Note (1)
6 data[ ] D Q ENA
RAM/ROM 256 x 16 512 x 8 1,024 x 4 Data In 2,048 x 2 4,096 x 1 Data Out D Q ENA
To MultiTrack Interconnect
address[ ]
D Q ENA
Address
wren
Write Enable outclken
inclken inclock
D Q ENA
Write Pulse Generator
outclock
Note to Figure 2-21:
(1) Violating the setup or hold time on the address registers could corrupt the memory contents. This applies to both read and write operations.
Global Clock Network & Phase-Locked Loops
Cyclone devices provide a global clock network and up to two PLLs for a complete clock management solution.
Global Clock Network
There are four dedicated clock pins (CLK[3..0], two pins on the left side and two pins on the right side) that drive the global clock network, as shown in Figure 2-22. PLL outputs, logic array, and dual-purpose clock (DPCLK[7..0]) pins can also drive the global clock network.
Altera Corporation January 2007
2-29 Preliminary
Cyclone Device Handbook, Volume 1
The eight global clock lines in the global clock network drive throughout the entire device. The global clock network can provide clocks for all resources within the device IOEs, LEs, and memory blocks. The global clock lines can also be used for control signals, such as clock enables and synchronous or asynchronous clears fed from the external pin, or DQS signals for DDR SDRAM or FCRAM interfaces. Internal logic can also drive the global clock network for internally generated global clocks and asynchronous clears, clock enables, or other control signals with large fanout. Figure 2-22 shows the various sources that drive the global clock network. Figure 2-22. Global Clock Generation Note (1)
DPCLK3
DPCLK2
Cyclone Device Global Clock Network 8 DPCLK1 From logic array 4 From logic array 4 DPCLK4
CLK0 CLK1 (3)
PLL1 2 4 4 2
PLL2 (2)
CLK2 CLK3 (3)
DPCLK0
DPCLK5
DPCLK7
DPCLK6
Notes to Figure 2-22:
(1) (2) (3) The EP1C3 device in the 100-pin TQFP package has five DPCLK pins (DPCLK2, DPCLK3, DPCLK4, DPCLK6, and DPCLK7). EP1C3 devices only contain one PLL (PLL 1). The EP1C3 device in the 100-pin TQFP package does not have dedicated clock pins CLK1 and CLK3.
2-30 Preliminary
Altera Corporation January 2007
Global Clock Network & Phase-Locked Loops
Dual-Purpose Clock Pins
Each Cyclone device except the EP1C3 device has eight dual-purpose clock pins, DPCLK[7..0] (two on each I/O bank). EP1C3 devices have five DPCLK pins in the 100-pin TQFP package. These dual-purpose pins can connect to the global clock network (see Figure 2-22) for high-fanout control signals such as clocks, asynchronous clears, presets, and clock enables, or protocol control signals such as TRDY and IRDY for PCI, or DQS signals for external memory interfaces.
Combined Resources
Each Cyclone device contains eight distinct dedicated clocking resources. The device uses multiplexers with these clocks to form six-bit buses to drive LAB row clocks, column IOE clocks, or row IOE clocks. See Figure 2-23. Another multiplexer at the LAB level selects two of the six LAB row clocks to feed the LE registers within the LAB. Figure 2-23. Global Clock Network Multiplexers
Column I/O Region IO_CLK]5..0]
Global Clock Network Global Clocks [3..0] Dual-Purpose Clocks [7..0] PLL Outputs [3..0] Core Logic [7..0] Clock [7..0]
LAB Row Clock [5..0]
Row I/O Region IO_CLK[5..0]
IOE clocks have row and column block regions. Six of the eight global clock resources feed to these row and column regions. Figure 2-24 shows the I/O clock regions.
Altera Corporation January 2007
2-31 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-24. I/O Clock Regions
Column I/O Clock Region IO_CLK[5..0]
6 I/O Clock Regions
Cyclone Logic Array
LAB Row Clocks labclk[5..0] 6 LAB Row Clocks labclk[5..0] 6 8 Global Clock Network
LAB Row Clocks labclk[5..0] 6 LAB Row Clocks labclk[5..0] 6
Row I/O Regions
LAB Row Clocks labclk[5..0] 6
LAB Row Clocks labclk[5..0] 6
I/O Clock Regions 6
Column I/O Clock Region IO_CLK[5..0]
PLLs
Cyclone PLLs provide general-purpose clocking with clock multiplication and phase shifting as well as outputs for differential I/O support. Cyclone devices contain two PLLs, except for the EP1C3 device, which contains one PLL.
2-32 Preliminary
Altera Corporation January 2007
Global Clock Network & Phase-Locked Loops
Table 2-6 shows the PLL features in Cyclone devices. Figure 2-25 shows a Cyclone PLL.
Table 2-6. Cyclone PLL Features Feature
Clock multiplication and division Phase shift Programmable duty cycle Number of internal clock outputs Number of external clock outputs Notes to Table 2-6:
(1) (2) (3) The m counter ranges from 2 to 32. The n counter and the post-scale counters range from 1 to 32. The smallest phase shift is determined by the voltage-controlled oscillator (VCO) period divided by 8. For degree increments, Cyclone devices can shift all output frequencies in increments of 45. Smaller degree increments are possible depending on the frequency and divide parameters. The EP1C3 device in the 100-pin TQFP package does not support external clock output. The EP1C6 device in the 144-pin TQFP package does not support external clock output from PLL2.
PLL Support
m/(n x post-scale counter) (1) Down to 125-ps increments (2), (3) Yes 2 One differential or one single-ended (4)
(4)
Figure 2-25. Cyclone PLL
Note (1)
VCO Phase Selection Selectable at Each PLL Output Port Post-Scale Counters
CLK0 or LVDSCLK1p (2) /n CLK1 or LVDSCLK1n (2)
t /m
/g0 Charge Pump Loop Filter
Global clock
t
PFD (3)
VCO
/g1
Global clock
/e
I/O buffer
Notes to Figure 2-25:
(1) (2) The EP1C3 device in the 100-pin TQFP package does not support external outputs or LVDS inputs. The EP1C6 device in the 144-pin TQFP package does not support external output from PLL2. LVDS input is supported via the secondary function of the dedicated clock pins. For PLL 1, the CLK0 pin's secondary function is LVDSCLK1p and the CLK1 pin's secondary function is LVDSCLK1n. For PLL 2, the CLK2 pin's secondary function is LVDSCLK2p and the CLK3 pin's secondary function is LVDSCLK2n. PFD: phase frequency detector.
(3)
Altera Corporation January 2007
2-33 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-26 shows the PLL global clock connections. Figure 2-26. Cyclone PLL Global Clock Connections
G1 G0 G2 G3 G4 G5 G6 G7
g0 CLK0 CLK1 (1) PLL1 g1 e PLL1_OUT (3), (4)
g0 g1 PLL2 e PLL2_OUT (3), (4) CLK2 CLK3 (2)
Notes to Figure 2-26:
(1) (2) (3) (4) PLL 1 supports one single-ended or LVDS input via pins CLK0 and CLK1. PLL2 supports one single-ended or LVDS input via pins CLK2 and CLK3. PLL1_OUT and PLL2_OUT support single-ended or LVDS output. If external output is not required, these pins are available as regular user I/O pins. The EP1C3 device in the 100-pin TQFP package does not support external clock output. The EP1C6 device in the 144-pin TQFP package does not support external clock output from PLL2.
Table 2-7 shows the global clock network sources available in Cyclone devices.
Table 2-7. Global Clock Network Sources (Part 1 of 2) Source
PLL Counter Output PLL1 G0 PLL1 G1 PLL2 G0 (1) PLL2 G1 (1) Dedicated Clock Input Pins CLK0 CLK1 (2) CLK2 CLK3 (2)
GCLK0
GCLK1 v
GCLK2 v
GCLK3
GCLK4
GCLK5
GCLK6
GCLK7
v
v v v v v
v v
v v v v v v
2-34 Preliminary
Altera Corporation January 2007
Global Clock Network & Phase-Locked Loops
Table 2-7. Global Clock Network Sources (Part 2 of 2) Source
Dual-Purpose Clock Pins DPCLK0 (3) DPCLK1 (3) DPCLK2 DPCLK3 DPCLK4 DPCLK5 (3) DPCLK6 DPCLK7 Notes to Table 2-7:
(1) (2) (3) EP1C3 devices only have one PLL (PLL 1). EP1C3 devices in the 100-pin TQFP package do not have dedicated clock pins CLK1 and CLK3. EP1C3 devices in the 100-pin TQFP package do not have the DPCLK0, DPCLK1, or DPCLK5 pins.
GCLK0
GCLK1
GCLK2
GCLK3 v
GCLK4
GCLK5
GCLK6
GCLK7
v v v v v v v
Clock Multiplication & Division
Cyclone PLLs provide clock synthesis for PLL output ports using m/(n x post scale counter) scaling factors. The input clock is divided by a pre-scale divider, n, and is then multiplied by the m feedback factor. The control loop drives the VCO to match fIN x (m/n). Each output port has a unique post-scale counter to divide down the high-frequency VCO. For multiple PLL outputs with different frequencies, the VCO is set to the least-common multiple of the output frequencies that meets its frequency specifications. Then, the post-scale dividers scale down the output frequency for each output port. For example, if the output frequencies required from one PLL are 33 and 66 MHz, the VCO is set to 330 MHz (the least-common multiple in the VCO's range). Each PLL has one pre-scale divider, n, that can range in value from 1 to 32. Each PLL also has one multiply divider, m, that can range in value from 2 to 32. Global clock outputs have two post scale G dividers for global clock outputs, and external clock outputs have an E divider for external clock output, both ranging from 1 to 32. The Quartus II software automatically chooses the appropriate scaling factors according to the input frequency, multiplication, and division values entered.
Altera Corporation January 2007
2-35 Preliminary
Cyclone Device Handbook, Volume 1
External Clock Inputs
Each PLL supports single-ended or differential inputs for sourcesynchronous receivers or for general-purpose use. The dedicated clock pins (CLK[3..0]) feed the PLL inputs. These dual-purpose pins can also act as LVDS input pins. See Figure 2-25. Table 2-8 shows the I/O standards supported by PLL input and output pins.
Table 2-8. PLL I/O Standards I/O Standard
3.3-V LVTTL/LVCMOS 2.5-V LVTTL/LVCMOS 1.8-V LVTTL/LVCMOS 1.5-V LVCMOS 3.3-V PCI LVDS SSTL-2 class I SSTL-2 class II SSTL-3 class I SSTL-3 class II Differential SSTL-2
CLK Input v v v v v v v v v v
EXTCLK Output v v v v v v v v v v v
For more information on LVDS I/O support, see "LVDS I/O Pins" on page 2-54.
External Clock Outputs
Each PLL supports one differential or one single-ended output for sourcesynchronous transmitters or for general-purpose external clocks. If the PLL does not use these PLL_OUT pins, the pins are available for use as general-purpose I/O pins. The PLL_OUT pins support all I/O standards shown in Table 2-8. The external clock outputs do not have their own VCC and ground voltage supplies. Therefore, to minimize jitter, do not place switching I/O pins next to these output pins. The EP1C3 device in the 100-pin TQFP package
2-36 Preliminary
Altera Corporation January 2007
Global Clock Network & Phase-Locked Loops
does not have dedicated clock output pins. The EP1C6 device in the 144-pin TQFP package only supports dedicated clock outputs from PLL 1.
Clock Feedback
Cyclone PLLs have three modes for multiplication and/or phase shifting:
Zero delay buffer mode The external clock output pin is phasealigned with the clock input pin for zero delay. Normal mode the design uses an internal PLL clock output, the If normal mode compensates for the internal clock delay from the input clock pin to the IOE registers. The external clock output pin is phase shifted with respect to the clock input pin if connected in this mode. You defines which internal clock output from the PLL should be phase-aligned to compensate for internal clock delay. No compensation mode this mode, the PLL will not compensate In for any clock networks.
Phase Shifting
Cyclone PLLs have an advanced clock shift capability that enables programmable phase shifts. You can enter a phase shift (in degrees or time units) for each PLL clock output port or for all outputs together in one shift. You can perform phase shifting in time units with a resolution range of 125 to 250 ps. The finest resolution equals one eighth of the VCO period. The VCO period is a function of the frequency input and the multiplication and division factors. Each clock output counter can choose a different phase of the VCO period from up to eight taps. You can use this clock output counter along with an initial setting on the post-scale counter to achieve a phase-shift range for the entire period of the output clock. The phase tap feedback to the m counter can shift all outputs to a single phase. The Quartus II software automatically sets the phase taps and counter settings according to the phase shift entered.
Lock Detect Signal
The lock output indicates that there is a stable clock output signal in phase with the reference clock. Without any additional circuitry, the lock signal may toggle as the PLL begins tracking the reference clock. Therefore, you may need to gate the lock signal for use as a systemcontrol signal. For correct operation of the lock circuit below -20 C, fIN/N > 200 MHz.
Altera Corporation January 2007
2-37 Preliminary
Cyclone Device Handbook, Volume 1
Programmable Duty Cycle
The programmable duty cycle allows PLLs to generate clock outputs with a variable duty cycle. This feature is supported on each PLL post-scale counter (g0, g1, e). The duty cycle setting is achieved by a low- and hightime count setting for the post-scale dividers. The Quartus II software uses the frequency input and the required multiply or divide rate to determine the duty cycle choices.
Control Signals
There are three control signals for clearing and enabling PLLs and their outputs. You can use these signals to control PLL resynchronization and the ability to gate PLL output clocks for low-power applications. The pllenable signal enables and disables PLLs. When the pllenable signal is low, the clock output ports are driven by ground and all the PLLs go out of lock. When the pllenable signal goes high again, the PLLs relock and resynchronize to the input clocks. An input pin or LE output can drive the pllenable signal. The areset signals are reset/resynchronization inputs for each PLL. Cyclone devices can drive these input signals from input pins or from LEs. When areset is driven high, the PLL counters will reset, clearing the PLL output and placing the PLL out of lock. When driven low again, the PLL will resynchronize to its input as it relocks. The pfdena signals control the phase frequency detector (PFD) output with a programmable gate. If you disable the PFD, the VCO will operate at its last set value of control voltage and frequency with some drift, and the system will continue running when the PLL goes out of lock or the input clock disables. By maintaining the last locked frequency, the system has time to store its current settings before shutting down. You can either use their own control signal or gated locked status signals to trigger the pfdena signal.
f
For more information on Cyclone PLLs, see Chapter 6, Using PLLs in Cyclone Devices.
2-38 Preliminary
Altera Corporation January 2007
I/O Structure
I/O Structure
IOEs support many features, including:

Differential and single-ended I/O standards 3.3-V, 64- and 32-bit, 66- and 33-MHz PCI compliance Joint Test Action Group (JTAG) boundary-scan test (BST) support Output drive strength control Weak pull-up resistors during configuration Slew-rate control Tri-state buffers Bus-hold circuitry Programmable pull-up resistors in user mode Programmable input and output delays Open-drain outputs DQ and DQS I/O pins
Cyclone device IOEs contain a bidirectional I/O buffer and three registers for complete embedded bidirectional single data rate transfer. Figure 2-27 shows the Cyclone IOE structure. The IOE contains one input register, one output register, and one output enable register. You can use the input registers for fast setup times and output registers for fast clockto-output times. Additionally, you can use the output enable (OE) register for fast clock-to-output enable timing. The Quartus II software automatically duplicates a single OE register that controls multiple output or bidirectional pins. IOEs can be used as input, output, or bidirectional pins.
Altera Corporation January 2007
2-39 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-27. Cyclone IOE Structure
Logic Array
OE Register OE D Q
Output Register Output D Q
Combinatorial input (1) Input Input Register D Q
Note to Figure 2-27:
(1) There are two paths available for combinatorial inputs to the logic array. Each path contains a unique programmable delay chain.
The IOEs are located in I/O blocks around the periphery of the Cyclone device. There are up to three IOEs per row I/O block and up to three IOEs per column I/O block (column I/O blocks span two columns). The row I/O blocks drive row, column, or direct link interconnects. The column I/O blocks drive column interconnects. Figure 2-28 shows how a row I/O block connects to the logic array. Figure 2-29 shows how a column I/O block connects to the logic array.
2-40 Preliminary
Altera Corporation January 2007
I/O Structure
Figure 2-28. Row I/O Block Connection to the Interconnect
R4 Interconnects
C4 Interconnects I/O Block Local Interconnect
21 Data and Control Signals from Logic Array (1) 21 Row I/O Block
LAB
io_datain[2..0] and comb_io_datain[2..0] (2)
Direct Link Interconnect to Adjacent LAB LAB Local Interconnect
Direct Link Interconnect from Adjacent LAB io_clk[5:0]
Row I/O Block Contains up to Three IOEs
Notes to Figure 2-28:
(1) The 21 data and control signals consist of three data out lines, io_dataout[2..0], three output enables, io_coe[2..0], three input clock enables, io_cce_in[2..0], three output clock enables, io_cce_out[2..0], three clocks, io_cclk[2..0], three asynchronous clear signals, io_caclr[2..0], and three synchronous clear signals, io_csclr[2..0]. Each of the three IOEs in the row I/O block can have one io_datain input (combinatorial or registered) and one comb_io_datain (combinatorial) input.
(2)
Altera Corporation January 2007
2-41 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-29. Column I/O Block Connection to the Interconnect
Column I/O Block Contains up to Three IOEs
Column I/O Block 21 Data & Control Signals from Logic Array (1) 21
IO_datain[2:0] & comb_io_datain[2..0] (2)
io_clk[5..0]
I/O Block Local Interconnect
R4 Interconnects
LAB
LAB
LAB
LAB Local Interconnect
C4 Interconnects
Notes to Figure 2-29:
(1) The 21 data and control signals consist of three data out lines, io_dataout[2..0], three output enables, io_coe[2..0], three input clock enables, io_cce_in[2..0], three output clock enables, io_cce_out[2..0], three clocks, io_cclk[2..0], three asynchronous clear signals, io_caclr[2..0], and three synchronous clear signals, io_csclr[2..0]. Each of the three IOEs in the column I/O block can have one io_datain input (combinatorial or registered) and one comb_io_datain (combinatorial) input.
(2)
2-42 Preliminary
Altera Corporation January 2007
I/O Structure
The pin's datain signals can drive the logic array. The logic array drives the control and data signals, providing a flexible routing resource. The row or column IOE clocks, io_clk[5..0], provide a dedicated routing resource for low-skew, high-speed clocks. The global clock network generates the IOE clocks that feed the row or column I/O regions (see "Global Clock Network & Phase-Locked Loops" on page 2-29). Figure 2-30 illustrates the signal paths through the I/O block. Figure 2-30. Signal Path through the I/O Block
Row or Column io_clk[5..0] To Other IOEs
To Logic Array
io_datain comb_io_datain oe ce_in io_csclr ce_out io_coe io_cce_in Data and Control Signal Selection aclr/preset sclr clk_in io_caclr clk_out io_cclk io_dataout dataout IOE
From Logic Array
io_cce_out
Each IOE contains its own control signal selection for the following control signals: oe, ce_in, ce_out, aclr/preset, sclr/preset, clk_in, and clk_out. Figure 2-31 illustrates the control signal selection.
Altera Corporation January 2007
2-43 Preliminary
Cyclone Device Handbook, Volume 1
Figure 2-31. Control Signal Selection per IOE
Dedicated I/O Clock [5..0] Local Interconnect Local Interconnect Local Interconnect Local Interconnect Local Interconnect Local Interconnect io_coe
io_csclr
io_caclr
io_cce_out
io_cce_in
clk_out
ce_out
sclr/preset
io_cclk
clk_in
ce_in
aclr/preset
oe
In normal bidirectional operation, you can use the input register for input data requiring fast setup times. The input register can have its own clock input and clock enable separate from the OE and output registers. The output register can be used for data requiring fast clock-to-output performance. The OE register is available for fast clock-to-output enable timing. The OE and output register share the same clock source and the same clock enable source from the local interconnect in the associated LAB, dedicated I/O clocks, or the column and row interconnects. Figure 2-32 shows the IOE in bidirectional configuration.
2-44 Preliminary
Altera Corporation January 2007
I/O Structure
Figure 2-32. Cyclone IOE in Bidirectional I/O Configuration
ioe_clk[5..0]
Column or Row Interconect
OE OE Register D PRN Q VCCIO Optional PCI Clamp VCCIO aclr/prn Programmable Pull-Up Resistor
clkout
ENA
CLRN
ce_out
Chip-Wide Reset Output Register D PRN Q Output Pin Delay Drive Strength Control Open-Drain Output Slew Control Input Pin to Logic Array Delay Bus Hold Input Pin to Input Register Delay or Input Pin to Logic Array Delay
ENA
sclr/preset CLRN
comb_datain data_in
Input Register PRN D Q clkin ce_in
ENA
CLRN
The Cyclone device IOE includes programmable delays to ensure zero hold times, minimize setup times, or increase clock to output times. A path in which a pin directly drives a register may require a programmable delay to ensure zero hold time, whereas a path in which a pin drives a register through combinatorial logic may not require the delay. Programmable delays decrease input-pin-to-logic-array and IOE input register delays. The Quartus II Compiler can program these delays
Altera Corporation January 2007
2-45 Preliminary
Cyclone Device Handbook, Volume 1
to automatically minimize setup time while providing a zero hold time. Programmable delays can increase the register-to-pin delays for output registers. Table 2-9 shows the programmable delays for Cyclone devices.
Table 2-9. Cyclone Programmable Delay Chain Programmable Delays
Input pin to logic array delay Input pin to input register delay Output pin delay
Quartus II Logic Option
Decrease input delay to internal cells Decrease input delay to input registers Increase delay to output pin
There are two paths in the IOE for a combinatorial input to reach the logic array. Each of the two paths can have a different delay. This allows you adjust delays from the pin to internal LE registers that reside in two different areas of the device. The designer sets the two combinatorial input delays by selecting different delays for two different paths under the Decrease input delay to internal cells logic option in the Quartus II software. When the input signal requires two different delays for the combinatorial input, the input register in the IOE is no longer available. The IOE registers in Cyclone devices share the same source for clear or preset. The designer can program preset or clear for each individual IOE. The designer can also program the registers to power up high or low after configuration is complete. If programmed to power up low, an asynchronous clear can control the registers. If programmed to power up high, an asynchronous preset can control the registers. This feature prevents the inadvertent activation of another device's active-low input upon power up. If one register in an IOE uses a preset or clear signal then all registers in the IOE must use that same signal if they require preset or clear. Additionally a synchronous reset signal is available to the designer for the IOE registers.
External RAM Interfacing
Cyclone devices support DDR SDRAM and FCRAM interfaces at up to 133 MHz through dedicated circuitry.
DDR SDRAM & FCRAM
Cyclone devices have dedicated circuitry for interfacing with DDR SDRAM. All I/O banks support DDR SDRAM and FCRAM I/O pins. However, the configuration input pins in bank 1 must operate at 2.5 V because the SSTL-2 VCCIO level is 2.5 V. Additionally, the configuration
2-46 Preliminary
Altera Corporation January 2007
I/O Structure
output pins (nSTATUS and CONF_DONE) and all the JTAG pins in I/O bank 3 must operate at 2.5 V because the VCCIO level of SSTL-2 is 2.5 V. I/O banks 1, 2, 3, and 4 support DQS signals with DQ bus modes of x 8. For x 8 mode, there are up to eight groups of programmable DQS and DQ pins, I/O banks 1, 2, 3, and 4 each have two groups in the 324-pin and 400-pin FineLine BGA packages. Each group consists of one DQS pin, a set of eight DQ pins, and one DM pin (see Figure 2-33). Each DQS pin drives the set of eight DQ pins within that group. Figure 2-33. Cyclone Device DQ & DQS Groups in x 8 Mode
Top, Bottom, Left, or Right I/O Bank
Note (1)
DQ Pins
DQS Pin
DM Pin
Note to Figure 2-33:
(1) Each DQ group consists of one DQS pin, eight DQ pins, and one DM pin.
Table 2-10 shows the number of DQ pin groups per device.
Table 2-10. DQ Pin Groups (Part 1 of 2) Device
EP1C3
Package
100-pin TQFP (1) 144-pin TQFP
Number of x 8 DQ Pin Groups
3 4 8 8
Total DQ Pin Count
24 32 64 64
EP1C4
324-pin FineLine BGA 400-pin FineLine BGA
Altera Corporation January 2007
2-47 Preliminary
Cyclone Device Handbook, Volume 1
Table 2-10. DQ Pin Groups (Part 2 of 2) Device
EP1C6
Package
144-pin TQFP 240-pin PQFP 256-pin FineLine BGA
Number of x 8 DQ Pin Groups
4 4 4 4 4 8 8 8
Total DQ Pin Count
32 32 32 32 32 64 64 64
EP1C12
240-pin PQFP 256-pin FineLine BGA 324-pin FineLine BGA
EP1C20
324-pin FineLine BGA 400-pin FineLine BGA
Note to Table 2-10:
(1) EP1C3 devices in the 100-pin TQFP package do not have any DQ pin groups in I/O bank 1.
A programmable delay chain on each DQS pin allows for either a 90 phase shift (for DDR SDRAM), or a 72 phase shift (for FCRAM) which automatically center-aligns input DQS synchronization signals within the data window of their corresponding DQ data signals. The phase-shifted DQS signals drive the global clock network. This global DQS signal clocks DQ signals on internal LE registers. These DQS delay elements combine with the PLL's clocking and phase shift ability to provide a complete hardware solution for interfacing to high-speed memory. The clock phase shift allows the PLL to clock the DQ output enable and output paths. The designer should use the following guidelines to meet 133 MHz performance for DDR SDRAM and FCRAM interfaces:

The DQS signal must be in the middle of the DQ group it clocks Resynchronize the incoming data to the logic array clock using successive LE registers or FIFO buffers LE registers must be placed in the LAB adjacent to the DQ I/O pin column it is fed by
Figure 2-34 illustrates DDR SDRAM and FCRAM interfacing from the I/O through the dedicated circuitry to the logic array.
2-48 Preliminary
Altera Corporation January 2007
I/O Structure
Figure 2-34. DDR SDRAM & FCRAM Interfacing
DQS
OE
OE LE Register
DQ
OE OE LE Register Output LE Register VCC t clk Output LE Register GND
OE LE Register
Output LE Registers OE LE Register DataA Input LE Registers -90 clk Output LE Registers DataB Input LE Registers Adjacent LAB LEs
PLL
Programmable Delay Chain
Global Clock Phase Shifted -90
LE Register
LE Register
Adjacent LAB LEs
Resynchronizing Global Clock
Programmable Drive Strength
The output buffer for each Cyclone device I/O pin has a programmable drive strength control for certain I/O standards. The LVTTL and LVCMOS standards have several levels of drive strength that the designer can control. SSTL-3 class I and II, and SSTL-2 class I and II support a minimum setting, the lowest drive strength that guarantees the IOH/IOL
Altera Corporation January 2007
2-49 Preliminary
Cyclone Device Handbook, Volume 1
of the standard. Using minimum settings provides signal slew rate control to reduce system noise and signal overshoot. Table 2-11 shows the possible settings for the I/O standards with drive strength control.
Table 2-11. Programmable Drive Strength Note (1) I/O Standard
LVTTL (3.3 V)
IOH/IOL Current Strength Setting (mA)
4 8 12 16 24(2)
LVCMOS (3.3 V)
2 4 8 12(2)
LVTTL (2.5 V)
2 8 12 16(2)
LVTTL (1.8 V)
2 8 12(2)
LVCMOS (1.5 V)
2 4 8(2)
Notes to Table 2-11:
(1) (2) SSTL-3 class I and II, SSTL-2 class I and II, and 3.3-V PCI I/O Standards do not support programmable drive strength. This is the default current strength setting in the Quartus II software.
Open-Drain Output
Cyclone devices provide an optional open-drain (equivalent to an opencollector) output for each I/O pin. This open-drain output enables the device to provide system-level control signals (e.g., interrupt and writeenable signals) that can be asserted by any of several devices.
2-50 Preliminary
Altera Corporation January 2007
I/O Structure
Slew-Rate Control
The output buffer for each Cyclone device I/O pin has a programmable output slew-rate control that can be configured for low noise or highspeed performance. A faster slew rate provides high-speed transitions for high-performance systems. However, these fast transitions may introduce noise transients into the system. A slow slew rate reduces system noise, but adds a nominal delay to rising and falling edges. Each I/O pin has an individual slew-rate control, allowing the designer to specify the slew rate on a pin-by-pin basis. The slew-rate control affects both the rising and falling edges.
Bus Hold
Each Cyclone device I/O pin provides an optional bus-hold feature. The bus-hold circuitry can hold the signal on an I/O pin at its last-driven state. Since the bus-hold feature holds the last-driven state of the pin until the next input signal is present, an external pull-up or pull-down resistor is not necessary to hold a signal level when the bus is tri-stated. The bus-hold circuitry also pulls undriven pins away from the input threshold voltage where noise can cause unintended high-frequency switching. The designer can select this feature individually for each I/O pin. The bus-hold output will drive no higher than VCCIO to prevent overdriving signals. If the bus-hold feature is enabled, the device cannot use the programmable pull-up option. Disable the bus-hold feature when the I/O pin is configured for differential signals. The bus-hold circuitry uses a resistor with a nominal resistance (RBH) of approximately 7 k to pull the signal level to the last-driven state. Table 4-15 on page 4-6 gives the specific sustaining current for each VCCIO voltage level driven through this resistor and overdrive current used to identify the next-driven input level. The bus-hold circuitry is only active after configuration. When going into user mode, the bus-hold circuit captures the value on the pin present at the end of configuration.
Programmable Pull-Up Resistor
Each Cyclone device I/O pin provides an optional programmable pullup resistor during user mode. If the designer enables this feature for an I/O pin, the pull-up resistor (typically 25 k) holds the output to the VCCIO level of the output pin's bank. Dedicated clock pins do not have the optional programmable pull-up resistor.
Altera Corporation January 2007
2-51 Preliminary
Cyclone Device Handbook, Volume 1
Advanced I/O Standard Support
Cyclone device IOEs support the following I/O standards:

3.3-V LVTTL/LVCMOS 2.5-V LVTTL/LVCMOS 1.8-V LVTTL/LVCMOS 1.5-V LVCMOS 3.3-V PCI LVDS RSDS SSTL-2 class I and II SSTL-3 class I and II Differential SSTL-2 class II (on output clocks only)
Table 2-12 describes the I/O standards supported by Cyclone devices.
Table 2-12. Cyclone I/O Standards I/O Standard
3.3-V LVTTL/LVCMOS 2.5-V LVTTL/LVCMOS 1.8-V LVTTL/LVCMOS 1.5-V LVCMOS 3.3-V PCI (1) LVDS (2) RSDS (2) SSTL-2 class I and II SSTL-3 class I and II Differential SSTL-2 (3) Notes to Table 2-12:
(1) There is no megafunction support for EP1C3 devices for the PCI compiler. However, EP1C3 devices support PCI by using the LVTTL 16-mA I/O standard and drive strength assignments in the Quartus II software. The device requires an external diode for PCI compliance. EP1C3 devices in the 100-pin TQFP package do not support the LVDS and RSDS I/O standards. This I/O standard is only available on output clock pins (PLL_OUT pins). EP1C3 devices in the 100-pin package do not support this I/O standard as it does not have PLL_OUT pins.
Type
Single-ended Single-ended Single-ended Single-ended Single-ended Differential Differential Voltage-referenced Voltage-referenced Differential
Output Supply Input Reference Voltage (VREF) (V) Voltage (VCCIO) (V)
N/A N/A N/A N/A N/A N/A N/A 1.25 1.5 1.25 3.3 2.5 1.8 1.5 3.3 2.5 2.5 2.5 3.3 2.5
Board Termination Voltage (VTT) (V)
N/A N/A N/A N/A N/A N/A N/A 1.25 1.5 1.25
(2) (3)
Cyclone devices contain four I/O banks, as shown in Figure 2-35. I/O banks 1 and 3 support all the I/O standards listed in Table 2-12. I/O banks 2 and 4 support all the I/O standards listed in Table 2-12 except the 3.3-V PCI standard. I/O banks 2 and 4 contain dual-purpose DQS, DQ,
2-52 Preliminary
Altera Corporation January 2007
I/O Structure
and DM pins to support a DDR SDRAM or FCRAM interface. I/O bank 1 can also support a DDR SDRAM or FCRAM interface, however, the configuration input pins in I/O bank 1 must operate at 2.5 V. I/O bank 3 can also support a DDR SDRAM or FCRAM interface, however, all the JTAG pins in I/O bank 3 must operate at 2.5 V. Figure 2-35. Cyclone I/O Banks Notes (1), (2)
I/O Bank 2
I/O Bank 1 Also Supports the 3.3-V PCI I/O Standard
I/O Bank 1
All I/O Banks Support 3.3-V LVTTL/LVCMOS 2.5-V LVTTL/LVCMOS 1.8-V LVTTL/LVCMOS 1.5-V LVCMOS LVDS RSDS SSTL-2 Class I and II SSTL-3 Class I and II
I/O Bank 3 Also Supports the 3.3-V PCI I/O Standard
I/O Bank 3
Individual Power Bus
I/O Bank 4
Notes to Figure 2-35:
(1) (2) Figure 2-35 is a top view of the silicon die. Figure 2-35 is a graphic representation only. Refer to the pin list and the Quartus II software for exact pin locations.
Each I/O bank has its own VCCIO pins. A single device can support 1.5-V, 1.8-V, 2.5-V, and 3.3-V interfaces; each individual bank can support a different standard with different I/O voltages. Each bank also has dualpurpose VREF pins to support any one of the voltage-referenced standards (e.g., SSTL-3) independently. If an I/O bank does not use voltage-referenced standards, the VREF pins are available as user I/O pins.
Altera Corporation January 2007
2-53 Preliminary
Cyclone Device Handbook, Volume 1
Each I/O bank can support multiple standards with the same VCCIO for input and output pins. For example, when VCCIO is 3.3-V, a bank can support LVTTL, LVCMOS, 3.3-V PCI, and SSTL-3 for inputs and outputs.
LVDS I/O Pins
A subset of pins in all four I/O banks supports LVDS interfacing. These dual-purpose LVDS pins require an external-resistor network at the transmitter channels in addition to 100- termination resistors on receiver channels. These pins do not contain dedicated serialization or deserialization circuitry; therefore, internal logic performs serialization and deserialization functions. Table 2-13 shows the total number of supported LVDS channels per device density.
Table 2-13. Cyclone Device LVDS Channels Device
EP1C3
Pin Count
100 144
Number of LVDS Channels
(1) 34 103 129 29 72 72 66 72 103 95 129
EP1C4
324 400
EP1C6
144 240 256
EP1C12
240 256 324
EP1C20
324 400
Note to Table 2-13:
(1) EP1C3 devices in the 100-pin TQFP package do not support the LVDS I/O standard.
MultiVolt I/O Interface
The Cyclone architecture supports the MultiVolt I/O interface feature, which allows Cyclone devices in all packages to interface with systems of different supply voltages. The devices have one set of VCC pins for internal operation and input buffers (VCCINT), and four sets for I/O output drivers (VCCIO).
2-54 Preliminary
Altera Corporation January 2007
Power Sequencing & Hot Socketing
The Cyclone VCCINT pins must always be connected to a 1.5-V power supply. If the VCCINT level is 1.5 V, then input pins are 1.5-V, 1.8-V, 2.5-V, and 3.3-V tolerant. The VCCIO pins can be connected to either a 1.5-V, 1.8-V, 2.5-V, or 3.3-V power supply, depending on the output requirements. The output levels are compatible with systems of the same voltage as the power supply (i.e., when VCCIO pins are connected to a 1.5-V power supply, the output levels are compatible with 1.5-V systems). When VCCIO pins are connected to a 3.3-V power supply, the output high is 3.3-V and is compatible with 3.3-V or 5.0-V systems. Table 2-14 summarizes Cyclone MultiVolt I/O support.
Table 2-14. Cyclone MultiVolt I/O Support VCCIO (V)
1.5 1.8 2.5 3.3 Notes to Table 2-14:
(1) (2)
Note (1) Output Signal 3.3 V
v (2) v (2)
Input Signal 1.5 V v v 1.8 V v v 2.5 V
v (2) v (2)
5.0 V
1.5 V v v (3) v (5)
1.8 V
2.5 V
3.3 V
5.0 V
v
v (5)
v v (4)
v v v (6)
v v (7) v v (8)
v (7)
v (7)
(3) (4) (5) (6) (7) (8)
The PCI clamping diode must be disabled to drive an input with voltages higher than VCCIO. When VCCIO = 1.5-V or 1.8-V and a 2.5-V or 3.3-V input signal feeds an input pin, higher pin leakage current is expected. Turn on Allow voltage overdrive for LVTTL / LVCMOS input pins in the Assignments > Device > Device and Pin Options > Pin Placement tab when a device has this I/O combinations. When VCCIO = 1.8-V, a Cyclone device can drive a 1.5-V device with 1.8-V tolerant inputs. When VCCIO = 3.3-V and a 2.5-V input signal feeds an input pin, the VCCIO supply current will be slightly larger than expected. When VCCIO = 2.5-V, a Cyclone device can drive a 1.5-V or 1.8-V device with 2.5-V tolerant inputs. Cyclone devices can be 5.0-V tolerant with the use of an external resistor and the internal PCI clamp diode. When VCCIO = 3.3-V, a Cyclone device can drive a 1.5-V, 1.8-V, or 2.5-V device with 3.3-V tolerant inputs. When VCCIO = 3.3-V, a Cyclone device can drive a device with 5.0-V LVTTL inputs but not 5.0-V LVCMOS inputs.
Power Sequencing & Hot Socketing
Because Cyclone devices can be used in a mixed-voltage environment, they have been designed specifically to tolerate any possible power-up sequence. Therefore, the VCCIO and VCCINT power supplies may be powered in any order. Signals can be driven into Cyclone devices before and during power up without damaging the device. In addition, Cyclone devices do not drive out during power up. Once operating conditions are reached and the device is configured, Cyclone devices operate as specified by the user.
Altera Corporation January 2007
2-55 Preliminary
Cyclone Device Handbook, Volume 1
Document Revision History
Table 2-15 shows the revision history for this document.
Table 2-15. Document Revision History Date & Document Version
January 2007 v1.5 August 2005 v1.4 February 2005 v1.3

Changes Made
Added document revision history. Updated Figures 2-17, 2-18, 2-19, 2-20, 2-21, and 2-32.
Summary of Changes
Minor updates.

Updated JTAG chain limits. Added test vector information. Corrected Figure 2-12. Added a note to Tables 2-17 through 2-21 regarding violating the setup or hold time. Updated phase shift information. Added 64-bit PCI support information.
October 2003 v1.2 September 2003 v1.1 May 2003 v1.0

Updated LVDS data rates to 640 Mbps from 311 Mbps. Added document to Cyclone Device Handbook.
2-56 Preliminary
Altera Corporation January 2007
3. Configuration & Testing
C51003-1.3
IEEE Std. 1149.1 (JTAG) Boundary Scan Support
All Cyclone(R) devices provide JTAG BST circuitry that complies with the IEEE Std. 1149.1a-1990 specification. JTAG boundary-scan testing can be performed either before or after, but not during configuration. Cyclone devices can also use the JTAG port for configuration together with either the Quartus(R) II software or hardware using either Jam Files (.jam) or Jam Byte-Code Files (.jbc). Cyclone devices support reconfiguring the I/O standard settings on the IOE through the JTAG BST chain. The JTAG chain can update the I/O standard for all input and output pins any time before or during user mode. Designers can use this ability for JTAG testing before configuration when some of the Cyclone pins drive or receive from other devices on the board using voltage-referenced standards. Since the Cyclone device might not be configured before JTAG testing, the I/O pins might not be configured for appropriate electrical standards for chip-to-chip communication. Programming those I/O standards via JTAG allows designers to fully test I/O connection to other devices. The JTAG pins support 1.5-V/1.8-V or 2.5-V/3.3-V I/O standards. The TDO pin voltage is determined by the VCCIO of the bank where it resides. The bank VCCIO selects whether the JTAG inputs are 1.5-V, 1.8-V, 2.5-V, or 3.3-V compatible. Cyclone devices also use the JTAG port to monitor the operation of the device with the SignalTap(R) II embedded logic analyzer. Cyclone devices support the JTAG instructions shown in Table 3-1.
Table 3-1. Cyclone JTAG Instructions (Part 1 of 2) JTAG Instruction
SAMPLE/PRELOAD
Instruction Code
00 0000 0101
Description
Allows a snapshot of signals at the device pins to be captured and examined during normal device operation, and permits an initial data pattern to be output at the device pins. Also used by the SignalTap II embedded logic analyzer. Allows the external circuitry and board-level interconnects to be tested by forcing a test pattern at the output pins and capturing test results at the input pins. Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through selected devices to adjacent devices during normal device operation.
EXTEST (1)
00 0000 0000
BYPASS
11 1111 1111
Altera Corporation January 2007
3-1 Preliminary
Cyclone Device Handbook, Volume 1
Table 3-1. Cyclone JTAG Instructions (Part 2 of 2) JTAG Instruction
USERCODE
Instruction Code
00 0000 0111
Description
Selects the 32-bit USERCODE register and places it between the TDI and TDO pins, allowing the USERCODE to be serially shifted out of TDO. Selects the IDCODE register and places it between TDI and TDO, allowing the IDCODE to be serially shifted out of TDO. Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through selected devices to adjacent devices during normal device operation, while tri-stating all of the I/O pins. Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through selected devices to adjacent devices during normal device operation while holding I/O pins to a state defined by the data in the boundary-scan register. Used when configuring a Cyclone device via the JTAG port with a MasterBlasterTM or ByteBlasterMVTM download cable, or when using a Jam File or Jam Byte-Code File via an embedded processor.
IDCODE HIGHZ (1)
00 0000 0110 00 0000 1011
CLAMP (1)
00 0000 1010
ICR instructions
PULSE_NCONFIG CONFIG_IO
00 0000 0001 00 0000 1101
Emulates pulsing the nCONFIG pin low to trigger reconfiguration even though the physical pin is unaffected. Allows configuration of I/O standards through the JTAG chain for JTAG testing. Can be executed before, after, or during configuration. Stops configuration if executed during configuration. Once issued, the CONFIG_IO instruction will hold nSTATUS low to reset the configuration device. nSTATUS is held low until the device is reconfigured. Monitors internal device operation with the SignalTap II embedded logic analyzer.
SignalTap II instructions Note to Table 3-1:
(1)
Bus hold and weak pull-up resistor features override the high-impedance state of HIGHZ, CLAMP, and EXTEST.
In the Quartus II software, there is an Auto Usercode feature where you can choose to use the checksum value of a programming file as the JTAG user code. If selected, the checksum is automatically loaded to the USERCODE register. Choose Assignments > Device > Device and Pin Options > General. Turn on Auto Usercode.
3-2 Preliminary
Altera Corporation January 2007
IEEE Std. 1149.1 (JTAG) Boundary Scan Support
The Cyclone device instruction register length is 10 bits and the USERCODE register length is 32 bits. Tables 3-2 and 3-3 show the boundary-scan register length and device IDCODE information for Cyclone devices.
Table 3-2. Cyclone Boundary-Scan Register Length Device
EP1C3 EP1C4 EP1C6 EP1C12 EP1C20
Boundary-Scan Register Length
339 930 582 774 930
Table 3-3. 32-Bit Cyclone Device IDCODE IDCODE (32 bits) (1) Device Version (4 Bits)
EP1C3 EP1C4 EP1C6 EP1C12 EP1C20
(1) (2)
Part Number (16 Bits)
0010 0000 1000 0001 0010 0000 1000 0101 0010 0000 1000 0010 0010 0000 1000 0011 0010 0000 1000 0100
Manufacturer Identity (11 Bits)
000 0110 1110 000 0110 1110 000 0110 1110 000 0110 1110 000 0110 1110
LSB (1 Bit) (2)
1 1 1 1 1
0000 0000 0000 0000 0000
Notes to Table 3-3:
The most significant bit (MSB) is on the left. The IDCODE's least significant bit (LSB) is always 1.
Altera Corporation January 2007
3-3 Preliminary
Cyclone Device Handbook, Volume 1
Figure 3-1 shows the timing requirements for the JTAG signals. Figure 3-1. Cyclone JTAG Waveforms
TMS
TDI t JCP t JCH TCK tJPZX TDO tJSSU Signal to Be Captured Signal to Be Driven tJSH t JPCO t JPXZ t JCL t JPSU t JPH
tJSZX
tJSCO
tJSXZ
Table 3-4 shows the JTAG timing parameters and values for Cyclone devices.
Table 3-4. Cyclone JTAG Timing Parameters & Values Symbol
tJ C P tJ C H tJ C L tJ P S U tJ P H tJ P C O tJ P Z X tJ P X Z tJ S S U tJ S H tJ S C O tJ S Z X tJ S X Z
Parameter
TCK clock period TCK clock high time TCK clock low time
JTAG port setup time JTAG port hold time JTAG port clock to output JTAG port high impedance to valid output JTAG port valid output to high impedance Capture register setup time Capture register hold time Update register clock to output Update register high impedance to valid output Update register valid output to high impedance
Min
100 50 50 20 45
Max
Unit
ns ns ns ns ns
25 25 25 20 45 35 35 35
ns ns ns ns ns ns ns ns
3-4 Preliminary
Altera Corporation January 2007
SignalTap II Embedded Logic Analyzer
1
Cyclone devices must be within the first 8 devices in a JTAG chain. All of these devices have the same JTAG controller. If any of the Cyclone devices are in the 9th or after they will fail configuration. This does not affect the SignalTap(R) II logic analyzer.
f
For more information on JTAG, see the following documents:

AN 39: IEEE Std. 1149.1 (JTAG) Boundary-Scan Testing in Altera Devices Jam Programming & Test Language Specification
SignalTap II Embedded Logic Analyzer
Cyclone devices feature the SignalTap II embedded logic analyzer, which monitors design operation over a period of time through the IEEE Std. 1149.1 (JTAG) circuitry. A designer can analyze internal logic at speed without bringing internal signals to the I/O pins. This feature is particularly important for advanced packages, such as FineLine BGA packages, because it can be difficult to add a connection to a pin during the debugging process after a board is designed and manufactured. The logic, circuitry, and interconnects in the Cyclone architecture are configured with CMOS SRAM elements. Altera FPGAs are reconfigurable and every device is tested with a high coverage production test program so the designer does not have to perform fault testing and can instead focus on simulation and design verification. Cyclone devices are configured at system power-up with data stored in an Altera configuration device or provided by a system controller. The Cyclone device's optimized interface allows the device to act as controller in an active serial configuration scheme with the new low-cost serial configuration device. Cyclone devices can be configured in under 120 ms using serial data at 20 MHz. The serial configuration device can be programmed via the ByteBlaster II download cable, the Altera Programming Unit (APU), or third-party programmers. In addition to the new low-cost serial configuration device, Altera offers in-system programmability (ISP)-capable configuration devices that can configure Cyclone devices via a serial data stream. The interface also enables microprocessors to treat Cyclone devices as memory and configure them by writing to a virtual memory location, making reconfiguration easy. After a Cyclone device has been configured, it can be reconfigured in-circuit by resetting the device and loading new data. Real-time changes can be made during system operation, enabling innovative reconfigurable computing applications.
Configuration
Altera Corporation January 2007
3-5 Preliminary
Cyclone Device Handbook, Volume 1
Operating Modes
The Cyclone architecture uses SRAM configuration elements that require configuration data to be loaded each time the circuit powers up. The process of physically loading the SRAM data into the device is called configuration. During initialization, which occurs immediately after configuration, the device resets registers, enables I/O pins, and begins to operate as a logic device. Together, the configuration and initialization processes are called command mode. Normal device operation is called user mode. SRAM configuration elements allow Cyclone devices to be reconfigured in-circuit by loading new configuration data into the device. With realtime reconfiguration, the device is forced into command mode with a device pin. The configuration process loads different configuration data, reinitializes the device, and resumes user-mode operation. Designers can perform in-field upgrades by distributing new configuration files either within the system or remotely. A built-in weak pull-up resistor pulls all user I/O pins to VCCIO before and during device configuration. The configuration pins support 1.5-V/1.8-V or 2.5-V/3.3-V I/O standards. The voltage level of the configuration output pins is determined by the VCCIO of the bank where the pins reside. The bank VCCIO selects whether the configuration inputs are 1.5-V, 1.8-V, 2.5-V, or 3.3-V compatible.
Configuration Schemes
Designers can load the configuration data for a Cyclone device with one of three configuration schemes (see Table 3-5), chosen on the basis of the target application. Designers can use a configuration device, intelligent controller, or the JTAG port to configure a Cyclone device. A low-cost configuration device can automatically configure a Cyclone device at system power-up.
3-6 Preliminary
Altera Corporation January 2007
Document Revision History
Multiple Cyclone devices can be configured in any of the three configuration schemes by connecting the configuration enable (nCE) and configuration enable output (nCEO) pins on each device.
Table 3-5. Data Sources for Configuration Configuration Scheme
Active serial Passive serial (PS)
Data Source
Low-cost serial configuration device Enhanced or EPC2 configuration device, MasterBlaster or ByteBlasterMV download cable, or serial data source MasterBlaster or ByteBlasterMV download cable or a microprocessor with a Jam or JBC file
JTAG
Document Revision History
Table 3-6 shows the revision history for this document.
Table 3-6. Document Revision History Date & Document Version
January 2007 v1.3 August 2005 V1.2 February 2005 V1.1 May 2003 v1.0

Changes Made
Added document revision history. Updated handpara note below Table 3-4.
Summary of Changes
Minor updates. Updated JTAG chain limits. Added information concerning test vectors. Added document to Cyclone Device Handbook.
Altera Corporation January 2007
3-7 Preliminary
Cyclone Device Handbook, Volume 1
3-8 Preliminary
Altera Corporation January 2007
4. DC & Switching Characteristics
C51004-1.6
Operating Conditions
Cyclone(R) devices are offered in both commercial, industrial, and extended temperature grades. However, industrial-grade and extendedtemperature-grade devices may have limited speed-grade availability. Tables 4-1 through 4-16 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for Cyclone devices.
Table 4-1. Cyclone Device Absolute Maximum Ratings Symbol
VCCINT VCCIO VCCA VI IOUT TSTG TAMB TJ Supply voltage DC input voltage DC output current, per pin Storage temperature Ambient temperature Junction temperature No bias Under bias
Notes (1), (2) Minimum
-0.5 -0.5
Parameter
Supply voltage
Conditions
With respect to ground (3)
Maximum
2.4 4.6 2.4 4.6 25 150 135 135
Unit
V V V V mA C C C
With respect to ground (3)
-0.5 -0.5 -25 -65 -65
BGA packages under bias
Table 4-2. Cyclone Device Recommended Operating Conditions (Part 1 of 2) Symbol
VCCINT VCCIO
Parameter
Supply voltage for internal logic and input buffers Supply voltage for output buffers, 3.3-V operation Supply voltage for output buffers, 2.5-V operation Supply voltage for output buffers, 1.8-V operation Supply voltage for output buffers, 1.5-V operation
Conditions
(4) (4) (4) (4) (4) (3), (5)
Minimum
1.425 3.00 2.375 1.71 1.4 -0.5
Maximum
1.575 3.60 2.625 1.89 1.6 4.1
Unit
V V V V V V
VI
Input voltage
Altera Corporation January 2007
4-1 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-2. Cyclone Device Recommended Operating Conditions (Part 2 of 2) Symbol
VO TJ
Parameter
Output voltage Operating junction temperature
Conditions
Minimum
0
Maximum
VCCIO 85 100 125
Unit
V C C C
For commercial use For industrial use For extendedtemperature use
0 -40 -40
Table 4-3. Cyclone Device DC Operating Conditions Symbol
II IOZ ICC0
Note (6) Minimum
-10 -10 4 6 6 8 12 15 20 30 50 25 45 65 100 1 50 70 100 150 2
Parameter
Input pin leakage current Tri-stated I/O pin leakage current VCC supply current (standby) (All M4K blocks in power-down mode) (7)
Conditions
VI = VC C I O m a x to 0 V (8) VO = VC C I O m a x to 0 V (8) EP1C3 EP1C4 EP1C6 EP1C12 EP1C20
Typica Maximum Unit l
10 10 A A mA mA mA mA mA k k k k k
RCONF (9) Value of I/O pin pull-up resistor VI = 0 V; VCCI0 = 3.3 V before and during configuration VI = 0 V; VCCI0 = 2.5 V VI = 0 V; VCCI0 = 1.8 V VI = 0 V; VCCI0 = 1.5 V Recommended value of I/O pin external pull-down resistor before and during configuration
Table 4-4. LVTTL Specifications (Part 1 of 2) Symbol
VCCIO VIH VIL
Parameter
Output supply voltage High-level input voltage Low-level input voltage
Conditions
Minimum
3.0 1.7 -0.5
Maximum
3.6 4.1 0.7
Unit
V V V
4-2 Preliminary
Altera Corporation January 2007
Operating Conditions
Table 4-4. LVTTL Specifications (Part 2 of 2) Symbol
VOH VOL
Parameter
High-level output voltage Low-level output voltage
Conditions
IOH = -4 to -24 mA (11) IOL = 4 to 24 mA (11)
Minimum
2.4
Maximum
Unit
V
0.45
V
Table 4-5. LVCMOS Specifications Symbol
VCCIO VIH VIL VOH VOL
Parameter
Output supply voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
3.0 1.7 -0.5
Maximum
3.6 4.1 0.7
Unit
V V V V
VCCIO = 3.0, IOH = -0.1 mA VCCIO = 3.0, IOL = 0.1 mA
VCCIO - 0.2 0.2
V
Table 4-6. 2.5-V I/O Specifications Symbol
VCCIO VIH VIL VOH
Parameter
Output supply voltage High-level input voltage Low-level input voltage High-level output voltage
Conditions
Minimum
2.375 1.7 -0.5
Maximum
2.625 4.1 0.7
Unit
V V V V V V
IOH = -0.1 mA IOH = -1 mA IOH = -2 to -16 mA (11)
2.1 2.0 1.7 0.2 0.4 0.7
VOL
Low-level output voltage
IOL = 0.1 mA IOH = 1 mA IOH = 2 to 16 mA (11)
V V V
Altera Corporation January 2007
4-3 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-7. 1.8-V I/O Specifications Symbol
VCCIO VI H VIL VOH VOL
Parameter
Output supply voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
1.65 0.65 x VCCIO -0.3
Maximum
1.95 2.25 (12) 0.35 x VCCIO
Unit
V V V V
IOH = -2 to -8 mA (11) IOL = 2 to 8 mA (11)
VCCIO - 0.45 0.45
V
Table 4-8. 1.5-V I/O Specifications Symbol
VCCIO VI H VIL VOH VOL
Parameter
Output supply voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
1.4 0.65 x VCCIO -0.3
Maximum
1.6 VCCIO + 0.3 (12) 0.35 x VCCIO 0.25 x VCCIO
Unit
V V V V V
IOH = -2 mA (11) IOL = 2 mA (11)
0.75 x VCCIO
Table 4-9. 2.5-V LVDS I/O Specifications Symbol
VCCIO VOD VOD VOS VOS VTH VIN RL
Note (13) Conditions Minimum
2.375
Parameter
I/O supply voltage Differential output voltage Change in VOD between high and low Output offset voltage Change in VOS between high and low Differential input threshold Receiver input voltage range Receiver differential input resistor
Typical
2.5
Maximum
2.625 550 50
Unit
V mV mV V mV mV V
RL = 100 RL = 100 RL = 100 RL = 100 VCM = 1.2 V
250
1.125
1.25
1.375 50
-100 0.0 90 100
100 2.4 110
4-4 Preliminary
Altera Corporation January 2007
Operating Conditions
Table 4-10. 3.3-V PCI Specifications Symbol
VCCIO VIH VIL VOH VOL
Parameter
Output supply voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
3.0 0.5 x VCCIO -0.5
Typical
3.3
Maximum
3.6 VCCIO + 0.5 0.3 x VCCIO
Unit
V V V V
IOUT = -500 A IOUT = 1,500 A
0.9 x VCCIO 0.1 x VCCIO
V
Table 4-11. SSTL-2 Class I Specifications Symbol
VCCIO VTT VREF VIH VIL VOH VOL
Parameter
Output supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
2.375 VR E F - 0.04 1.15 VR E F + 0.18 -0.3
Typical
2.5 VR E F 1.25
Maximum
2.625 VR E F + 0.04 1.35 3.0 VR E F - 0.18
Unit
V V V V V V
IOH = -8.1 mA (11) IOL = 8.1 mA (11)
VTT + 0.57 VT T - 0.57
V
Table 4-12. SSTL-2 Class II Specifications Symbol
VCCIO VTT VREF VIH VIL VOH VOL
Parameter
Output supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
2.3 VR E F - 0.04 1.15 VR E F + 0.18 -0.3
Typical
2.5 VR E F 1.25
Maximum
2.7 VR E F + 0.04 1.35 VCCIO + 0.3 VR E F - 0.18
Unit
V V V V V V
IOH = -16.4 mA (11) IOL = 16.4 mA (11)
VTT + 0.76 VT T - 0.76
V
Altera Corporation January 2007
4-5 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-13. SSTL-3 Class I Specifications Symbol
VCCIO VTT VREF VIH VIL VOH VOL
Parameter
Output supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
3.0 VR E F - 0.05 1.3 VR E F + 0.2 -0.3
Typical
3.3 VR E F 1.5
Maximum
3.6 VR E F + 0.05 1.7 VCCIO + 0.3 VR E F - 0.2
Unit
V V V V V V
IOH = -8 mA (11) IOL = 8 mA (11)
VTT + 0.6 VT T - 0.6
V
Table 4-14. SSTL-3 Class II Specifications Symbol
VCCIO VTT VREF VIH VIL VOH VOL
Parameter
Output supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage
Conditions
Minimum
3.0 VR E F - 0.05 1.3 VR E F + 0.2 -0.3
Typical
3.3 VR E F 1.5
Maximum
3.6 VR E F + 0.05 1.7 VCCIO + 0.3 VR E F - 0.2
Unit
V V V V V V
IOH = -16 mA (11) IOL = 16 mA (11)
VT T + 0.8 VTT - 0.8
V
Table 4-15. Bus Hold Parameters VC C I O Level Parameter Conditions 1.5 V Min
Low sustaining current VIN > VIL (maximum)
1.8 V Min
30 -30 200 -200
2.5 V Min
50 -50 300 -300
3.3 V Min
70 -70 500 -500
Unit
Max
Max
Max
Max
A A A A
High sustaining VIN < VIH current (minimum) Low overdrive current High overdrive current 0 V < VIN < VCCIO 0 V < VIN < VCCIO
4-6 Preliminary
Altera Corporation January 2007
Operating Conditions
Table 4-16. Cyclone Device Capacitance Symbol
CIO CLVDS CVREF CDPCLK CCLK
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12)
Note (14) Typical
4.0 4.7 12.0 4.4 4.7
Parameter
Input capacitance for user I/O pin Input capacitance for dual-purpose LVDS/user I/O pin Input capacitance for dual-purpose VR E F /user I/O pin. Input capacitance for dual-purpose DPCLK/user I/O pin. Input capacitance for CLK pin.
Unit
pF pF pF pF pF
Notes to Tables 4-1 through 4-16:
Refer to the Operating Requirements for Altera Devices Data Sheet. Conditions beyond those listed in Table 4-1 may cause permanent damage to a device. Additionally, device operation at the absolute maximum ratings for extended periods of time may have adverse affects on the device. Minimum DC input is -0.5 V. During transitions, the inputs may undershoot to -2.0 V or overshoot to 4.6 V for input currents less than 100 mA and periods shorter than 20 ns. Maximum VCC rise time is 100 ms, and VCC must rise monotonically. All pins, including dedicated inputs, clock, I/O, and JTAG pins, may be driven before VCCINT and VCCIO are powered. Typical values are for TA = 25 C, VCCINT = 1.5 V, and VCCIO = 1.5 V, 1.8 V, 2.5 V, and 3.3 V. VI = ground, no load, no toggling inputs. This value is specified for normal device operation. The value may vary during power-up. This applies for all VCCIO settings (3.3, 2.5, 1.8, and 1.5 V). RCONF is the measured value of internal pull-up resistance when the I/O pin is tied directly to GND. RCONF value will be lower if an external source drives the pin higher than VC C I O . Pin pull-up resistance values will lower if an external source drives the pin higher than VCCIO. Drive strength is programmable according to values in Chapter 2, Cyclone Architecture, Table 2-11. Overdrive is possible when a 1.5 V or 1.8 V and a 2.5 V or 3.3 V input signal feeds an input pin. Turn on "Allow voltage overdrive" for LVTTL/LVCMOS input pins in the Assignments > Device > Device and Pin Options > Pin Placement tab when a device has this I/O combination. However, higher leakage current is expected. The Cyclone LVDS interface requires a resistor network outside of the transmitter channels. Capacitance is sample-tested only. Capacitance is measured using time-domain reflections (TDR). Measurement accuracy is within 0.5 pF.
(13) (14)
Altera Corporation January 2007
4-7 Preliminary
Cyclone Device Handbook, Volume 1
Power Consumption
Designers can use the Altera web Early Power Estimator to estimate the device power. Cyclone devices require a certain amount of power-up current to successfully power up because of the nature of the leading-edge process on which they are fabricated. Table 4-17 shows the maximum power-up current required to power up a Cyclone device.
Table 4-17. Cyclone Maximum Power-Up Current (ICCINT) Requirements (In-Rush Current) Device
EP1C3 EP1C4 EP1C6 EP1C12 EP1C20 Notes to Table 4-17:
(1) (2) (3) The Cyclone devices (except for the EP1C20 device) meet the power up specification for Mini PCI. The lot codes 9G0082 to 9G2999, or 9G3109 and later comply to the specifications in Table 4-17 and meet the Mini PCI specification. Lot codes appear at the top of the device. The lot codes 9H0004 to 9H29999, or 9H3014 and later comply to the specifications in this table and meet the Mini PCI specification. Lot codes appear at the top of the device.
Commercial Specification
150 150 175 300 500
Industrial Specification
180 180 210 360 600
Unit
mA mA mA mA mA
Designers should select power supplies and regulators that can supply this amount of current when designing with Cyclone devices. This specification is for commercial operating conditions. Measurements were performed with an isolated Cyclone device on the board. Decoupling capacitors were not used in this measurement. To factor in the current for decoupling capacitors, sum up the current for each capacitor using the following equation: I = C (dV/dt) The exact amount of current that is consumed varies according to the process, temperature, and power ramp rate. If the power supply or regulator can supply more current than required, the Cyclone device may consume more current than the maximum current specified in Table 4-17. However, the device does not require any more current to successfully power up than what is listed in Table 4-17. The duration of the ICCINT power-up requirement depends on the VCCINT voltage supply rise time. The power-up current consumption drops when the VCCINT supply reaches approximately 0.75 V. For example, if the VCCINT rise time has a linear rise of 15 ms, the current consumption spike drops by 7.5 ms.
4-8 Preliminary
Altera Corporation January 2007
Timing Model
Typically, the user-mode current during device operation is lower than the power-up current in Table 4-17. Altera recommends using the Cyclone Power Calculator, available on the Altera web site, to estimate the user-mode ICCINT consumption and then select power supplies or regulators based on the higher value.
Timing Model
The DirectDrive technology and MultiTrack interconnect ensure predictable performance, accurate simulation, and accurate timing analysis across all Cyclone device densities and speed grades. This section describes and specifies the performance, internal, external, and PLL timing specifications. All specifications are representative of worst-case supply voltage and junction temperature conditions.
Preliminary & Final Timing
Timing models can have either preliminary or final status. The Quartus(R) II software issues an informational message during the design compilation if the timing models are preliminary. Table 4-18 shows the status of the Cyclone device timing models. Preliminary status means the timing model is subject to change. Initially, timing numbers are created using simulation results, process data, and other known parameters. These tests are used to make the preliminary numbers as close to the actual timing parameters as possible. Final timing numbers are based on actual device operation and testing. These numbers reflect the actual performance of the device under worst-case voltage and junction temperature conditions.
Table 4-18. Cyclone Device Timing Model Status Device
EP1C3 EP1C4 EP1C6 EP1C12 EP1C20
Preliminary
Final v v v v v
Altera Corporation January 2007
4-9 Preliminary
Cyclone Device Handbook, Volume 1
Performance
The maximum internal logic array clock tree frequency is limited to the specifications shown in Table 4-19.
Table 4-19. Clock Tree Maximum Performance Specification -6 Speed Grade Parameter
Clock tree fM A X
-7 Speed Grade Min Typ Max
320
-8 Speed Grade Units Min Typ Max
275 MHz
Definition Min
Maximum frequency that the clock tree can support for clocking registered logic
Typ
Max
405
Table 4-20 shows the Cyclone device performance for some common designs. All performance values were obtained with the Quartus II software compilation of library of parameterized modules (LPM) functions or megafunctions. These performance values are based on EP1C6 devices in 144-pin TQFP packages.
Table 4-20. Cyclone Device Performance Resources Used Resource Used
LE
Performance
Design Size & Function
16-to-1 multiplexer 32-to-1 multiplexer 16-bit counter 64-bit counter (1) -
Mode LEs
21 44 16 66
M4K Memory Bits
-
M4K -6 Speed -7 Speed -8 Speed Memory Grade Grade Grade Blocks (MHz) (MHz) (MHz)
405.00 317.36 405.00 208.99 320.00 284.98 320.00 181.98 275.00 260.15 275.00 160.75
4-10 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-20. Cyclone Device Performance Resources Used Resource Used
M4K memory block
Performance
Design Size & Function
RAM 128 x 36 bit RAM 128 x 36 bit
Mode LEs
Single port Simple dual-port mode True dualport mode -
M4K Memory Bits
4,608 4,608
M4K -6 Speed -7 Speed -8 Speed Memory Grade Grade Grade Blocks (MHz) (MHz) (MHz)
1 1 256.00 255.95 222.67 222.67 197.01 196.97
RAM 256 x 18 bit
40 11
4,608 4,608 4,536
1 1 1
255.95 256.02 255.95
222.67 222.67 222.67
196.97 197.01 196.97
FIFO 128 x 36 bit Shift register 9 x 4 x 128 Note to Table 4-20:
(1)
Shift register
The performance numbers for this function are from an EP1C6 device in a 240-pin PQFP package.
Internal Timing Parameters
Internal timing parameters are specified on a speed grade basis independent of device density. Tables 4-21 through 4-24 describe the Cyclone device internal timing microparameters for LEs, IOEs, M4K memory structures, and MultiTrack interconnects.
Table 4-21. LE Internal Timing Microparameter Descriptions Symbol
tSU tH tCO tLUT tCLR tPRE tCLKHL
Parameter
LE register setup time before clock LE register hold time after clock LE register clock-to-output delay LE combinatorial LUT delay for data-in to data-out Minimum clear pulse width Minimum preset pulse width Minimum clock high or low time
Altera Corporation January 2007
4-11 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-22. IOE Internal Timing Microparameter Descriptions Symbol
tSU tH tCO tPIN2COMBOUT_R tPIN2COMBOUT_C tCOMBIN2PIN_R tCOMBIN2PIN_C tCLR tPRE tCLKHL
Parameter
IOE input and output register setup time before clock IOE input and output register hold time after clock IOE input and output register clock-to-output delay Row input pin to IOE combinatorial output Column input pin to IOE combinatorial output Row IOE data input to combinatorial output pin Column IOE data input to combinatorial output pin Minimum clear pulse width Minimum preset pulse width Minimum clock high or low time
Table 4-23. M4K Block Internal Timing Microparameter Descriptions Symbol
tM4KRC tM4KWC tM4KWERESU tM4KWEREH tM4KBESU tM4KBEH tM4KDATAASU tM4KDATAAH tM4KADDRASU tM4KADDRAH tM4KDATABSU tM4KDATABH tM4KADDRBSU tM4KADDRBH tM4KDATACO1 tM4KDATACO2 tM4KCLKHL tM4KCLR
Parameter
Synchronous read cycle time Synchronous write cycle time Write or read enable setup time before clock Write or read enable hold time after clock Byte enable setup time before clock Byte enable hold time after clock A port data setup time before clock A port data hold time after clock A port address setup time before clock A port address hold time after clock B port data setup time before clock B port data hold time after clock B port address setup time before clock B port address hold time after clock Clock-to-output delay when using output registers Clock-to-output delay without output registers Minimum clock high or low time Minimum clear pulse width
4-12 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-24. Routing Delay Internal Timing Microparameter Descriptions Symbol
tR4 tC4 tLOCAL
Parameter
Delay for an R4 line with average loading; covers a distance of four LAB columns Delay for an C4 line with average loading; covers a distance of four LAB rows Local interconnect delay
Figure 4-1 shows the memory waveforms for the M4K timing parameters shown in Table 4-23. Figure 4-1. Dual-Port RAM Timing Microparameter Waveform
wrclock tWEREH wren tWADDRSU wraddress an-1 tDATAH data-in din-1 tDATASU rdclock tWERESU rden tRC rdaddress bn b0 tDATACO1 reg_data-out doutn-2 doutn-1 tDATACO2 unreg_data-out doutn-1 doutn dout0 doutn dout0 b1 b2 b3 tWEREH din din4 din5 din6 an a0 a1 a2 a3 a4 tWADDRH a5 a6 tWERESU
Altera Corporation January 2007
4-13 Preliminary
Cyclone Device Handbook, Volume 1
Internal timing parameters are specified on a speed grade basis independent of device density. Tables 4-25 through 4-28 show the internal timing microparameters for LEs, IOEs, TriMatrix memory structures, DSP blocks, and MultiTrack interconnects.
Table 4-25. LE Internal Timing Microparameters -6 Symbol Min
tSU tH tCO tLUT tCLR tPRE tCLKHL 129 129 1,234 29 12 173 454 148 148 1,562
-7 Max Min
33 13 198 522 167 167 1,818
-8 Unit Max Min
37 15 224 590
Max
ps ps ps ps ps ps ps
Table 4-26. IOE Internal Timing Microparameters -6 Symbol Min
tSU tH tCO tPIN2COMBOUT_R tPIN2COMBOUT_C tCOMBIN2PIN_R tCOMBIN2PIN_C tCLR tPRE tCLKHL 280 280 1,234 348 0 511 1,130 1,135 2,627 2,615 322 322 1,562
-7 Max Min
400 0 587 1,299 1,305 3,021 3,007 364 364 1,818
-8 Unit Max Min
452 0 664 1,469 1,475 3,415 3,399
Max
ps ps ps ps ps ps ps ps ps ps
4-14 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-27. M4K Block Internal Timing Microparameters -6 Symbol Min
tM4KRC tM4KWC tM4KWERESU tM4KWEREH tM4KBESU tM4KBEH tM4KDATAASU tM4KDATAAH tM4KADDRASU tM4KADDRAH tM4KDATABSU tM4KDATABH tM4KADDRBSU tM4KADDRBH tM4KDATACO1 tM4KDATACO2 tM4KCLKHL tM4KCLR 1,234 286 72 43 72 43 72 43 72 43 72 43 72 43 621 4,351 1,562 328
-7 Max
4,379 2,910 82 49 82 49 82 49 82 49 82 49 82 49 714 5,003 1,818 371
-8 Unit Max
5,035 3,346 93 55 93 55 93 55 93 55 93 55 93 55 807 5,656
Min
Min
Max
5,691 3,783 ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps
Table 4-28. Routing Delay Internal Timing Microparameters -6 Symbol Min
tR4 tC4 tLOCAL
-7 Max
261 338 244
-8 Unit Max
300 388 281
Min
Min
Max
339 439 318 ps ps ps
External Timing Parameters
External timing parameters are specified by device density and speed grade. Figure 4-2 shows the timing model for bidirectional IOE pin timing. All registers are within the IOE.
Altera Corporation January 2007
4-15 Preliminary
Cyclone Device Handbook, Volume 1
Figure 4-2. External Timing in Cyclone Devices
OE Register D PRN Q
Dedicated Clock
CLRN Output Register D PRN Q
tXZ tZX tINSU tINH tOUTCO
Bidirectional Pin
CLRN
Input Register PRN D Q
CLRN
All external I/O timing parameters shown are for 3.3-V LVTTL I/O standard with the maximum current strength and fast slew rate. For external I/O timing using standards other than LVTTL or for different current strengths, use the I/O standard input and output delay adders in Tables 4-40 through 4-44. Table 4-29 shows the external I/O timing parameters when using global clock networks.
Table 4-29. Cyclone Global Clock External I/O Timing Parameters Symbol
tI N S U tI N H tO U T C O tI N S U P L L
Notes (1), (2) (Part 1 of 2) Conditions
Parameter
Setup time for input or bidirectional pin using IOE input register with global clock fed by CLK pin Hold time for input or bidirectional pin using IOE input register with global clock fed by CLK pin Clock-to-output delay output or bidirectional pin using IOE output register with global clock fed by CLK pin Setup time for input or bidirectional pin using IOE input register with global clock fed by Enhanced PLL with default phase setting Hold time for input or bidirectional pin using IOE input register with global clock fed by enhanced PLL with default phase setting
CLOAD = 10 pF
tI N H P L L
4-16 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-29. Cyclone Global Clock External I/O Timing Parameters Symbol
tO U T C O P L L
Notes (1), (2) (Part 2 of 2) Conditions
CLOAD = 10 pF
Parameter
Clock-to-output delay output or bidirectional pin using IOE output register with global clock enhanced PLL with default phase setting
Notes to Table 4-29:
(1) (2) These timing parameters are sample-tested only. These timing parameters are for IOE pins using a 3.3-V LVTTL, 24-mA setting. Designers should use the Quartus II software to verify the external timing for any pin.
Tables 4-30 through 4-31 show the external timing parameters on column and row pins for EP1C3 devices.
Table 4-30. EP1C3 Column Pin Global Clock External I/O Timing Parameters -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L 3.085 0.000 2.000 1.795 0.000 0.500 2.306 4.073
-7 Speed Grade Min
3.547 0.000 2.000 2.063 0.000 0.500 2.651 4.682
-8 Speed Grade Unit Min
4.009 0.000 2.000 2.332 0.000 0.500 2.998 5.295
Max
Max
Max
ns ns ns ns ns ns
Table 4-31. EP1C3 Row Pin Global Clock External I/O Timing Parameters -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L 3.157 0.000 2.000 1.867 0.000 0.500 2.217 3.984
-7 Speed Grade Min
3.630 0.000 2.000 2.146 0.000 0.500 2.549 4.580
-8 Speed Grade Unit Min
4.103 0.000 2.000 2.426 0.000 0.500 2.883 5.180
Max
Max
Max
ns ns ns ns ns ns
Altera Corporation January 2007
4-17 Preliminary
Cyclone Device Handbook, Volume 1
Tables 4-32 through 4-33 show the external timing parameters on column and row pins for EP1C4 devices.
Table 4-32. EP1C4 Column Pin Global Clock External I/O Timing Parameters Note (1) -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L 2.471 0.000 2.000 1.471 0.000 0.500 2.080 3.937
-7 Speed Grade Min
2.841 0.000 2.000 1.690 0.000 0.500 2.392 4.526
-8 Speed Grade Unit Min
3.210 0.000 2.000 1.910 0.000 0.500 2.705 5.119
Max
Max
Max
ns ns ns ns ns ns
Table 4-33. EP1C4 Row Pin Global Clock External I/O Timing Parameters Note (1) -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L
(1)
-7 Speed Grade Min
2.990 0.000
-8 Speed Grade Unit Min
3.379 0.000
Max
Max
Max
ns ns 5.189 ns ns ns 2.905 ns
2.600 0.000 2.000 1.300 0.000 0.500 2.234 3.991
2.000 1.494 0.000 0.500
4.388
2.000 1.689 0.000
2.569
0.500
Note to Tables 4-32 and 4-33:
Contact Altera Applications for EP1C4 device timing parameters.
4-18 Preliminary
Altera Corporation January 2007
Timing Model
Tables 4-34 through 4-35 show the external timing parameters on column and row pins for EP1C6 devices.
Table 4-34. EP1C6 Column Pin Global Clock External I/O Timing Parameters -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L 2.691 0.000 2.000 1.513 0.000 0.500 2.038 3.917
-7 Speed Grade Min
3.094 0.000 2.000 1.739 0.000 0.500 2.343 4.503
-8 Speed Grade Unit Min
3.496 0.000 2.000 1.964 0.000 0.500 2.651 5.093
Max
Max
Max
ns ns ns ns ns ns
Table 4-35. EP1C6 Row Pin Global Clock External I/O Timing Parameters -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L 2.774 0.000 2.000 1.596 0.000 0.500 1.938 3.817
-7 Speed Grade Min
3.190 0.000 2.000 1.835 0.000 0.500 2.228 4.388
-8 Speed Grade Unit Min
3.605 0.000 2.000 2.073 0.000 0.500 2.521 4.963
Max
Max
Max
ns ns ns ns ns ns
Tables 4-36 through 4-37 show the external timing parameters on column and row pins for EP1C12 devices.
Table 4-36. EP1C12 Column Pin Global Clock External I/O Timing Parameters (Part 1 of 2) -6 Speed Grade Symbol Min
tI N S U tI N H tOU T C O tI N S U P L L 2.510 0.000 2.000 1.588 3.798
-7 Speed Grade Min
2.885 0.000 2.000 1.824 4.367
-8 Speed Grade Unit Min
3.259 0.000 2.000 2.061 4.940
Max
Max
Max
ns ns ns ns
Altera Corporation January 2007
4-19 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-36. EP1C12 Column Pin Global Clock External I/O Timing Parameters (Part 2 of 2) -6 Speed Grade Symbol Min
tI N H P L L tO U T C O P L L 0.000 0.500 1.663
-7 Speed Grade Min
0.000 0.500 1.913
-8 Speed Grade Unit Min
0.000 0.500 2.164
Max
Max
Max
ns ns
Table 4-37. EP1C12 Row Pin Global Clock External I/O Timing Parameters -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L 2.620 0.000 2.000 1.698 0.000 0.500 1.536 3.671
-7 Speed Grade Min
3.012 0.000 2.000 1.951 0.000 0.500 1.767 4.221
-8 Speed Grade Unit Min
3.404 0.000 2.000 2.206 0.000 0.500 1.998 4.774
Max
Max
Max
ns ns ns ns ns ns
Tables 4-38 through 4-39 show the external timing parameters on column and row pins for EP1C20 devices.
Table 4-38. EP1C20 Column Pin Global Clock External I/O Timing Parameters -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tI N S U P L L tI N H P L L tO U T C O P L L 2.417 0.000 2.000 1.417 0.000 0.500 1.667 3.724
-7 Speed Grade Min
2.779 0.000 2.000 1.629 0.000 0.500 1.917 4.282
-8 Speed Grade Unit Min
3.140 0.000 2.000 1.840 0.000 0.500 2.169 4.843
Max
Max
Max
ns ns ns ns ns ns
4-20 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-39. EP1C20 Row Pin Global Clock External I/O Timing Parameters -6 Speed Grade Symbol Min
tI N S U tI N H tO U T C O tX Z tZ X tI N S U P L L tI N H P L L tO U T C O P L L tX Z P L L tZ X P L L 1.417 0.000 0.500 1.667 1.588 1.588 2.417 0.000 2.000 3.724 3.645 3.645 1.629 0.000 0.500 1.917 1.826 1.826
-7 Speed Grade Min
2.779 0.000 2.000 4.282 4.191 4.191
-8 Speed Grade Unit Min
3.140 0.000 2.000 4.843 4.740 4.740 1.840 0.000 0.500 2.169 2.066 2.066
Max
Max
Max
ns ns ns ns ns ns ns ns ns ns
External I/O Delay Parameters
External I/O delay timing parameters for I/O standard input and output adders and programmable input and output delays are specified by speed grade independent of device density. Tables 4-40 through 4-45 show the adder delays associated with column and row I/O pins for all packages. If an I/O standard is selected other than LVTTL 4 mA with a fast slew rate, add the selected delay to the external tCO and tSU I/O parameters shown in Tables 4-25 through 4-28.
Table 4-40. Cyclone I/O Standard Column Pin Input Delay Adders (Part 1 of 2) -6 Speed Grade I/O Standard Min
LVCMOS 3.3-V LVTTL 2.5-V LVTTL 1.8-V LVTTL 1.5-V LVTTL SSTL-3 class I SSTL-3 class II SSTL-2 class I
-7 Speed Grade Min Max
0 0 31 209 319 - 288 - 288 - 320
-8 Speed Grade Unit Min Max
0 0 35 236 361 - 325 - 325 - 362 ps ps ps ps ps ps ps ps
Max
0 0 27 182 278 - 250 - 250 - 278
Altera Corporation January 2007
4-21 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-40. Cyclone I/O Standard Column Pin Input Delay Adders (Part 2 of 2) -6 Speed Grade I/O Standard Min
SSTL-2 class II LVDS
-7 Speed Grade Min Max
- 320 - 301
-8 Speed Grade Unit Min Max
- 362 - 340 ps ps
Max
- 278 - 261
Table 4-41. Cyclone I/O Standard Row Pin Input Delay Adders -6 Speed Grade I/O Standard Min
LVCMOS 3.3-V LVTTL 2.5-V LVTTL 1.8-V LVTTL 1.5-V LVTTL 3.3-V PCI (1) SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II LVDS
-7 Speed Grade Min Max
0 0 31 209 319 0 - 288 - 288 - 320 - 320 - 301
-8 Speed Grade Unit Min Max
0 0 35 236 361 0 - 325 - 325 - 362 - 362 - 340 ps ps ps ps ps ps ps ps ps ps ps
Max
0 0 27 182 278 0 - 250 - 250 - 278 - 278 - 261
Table 4-42. Cyclone I/O Standard Output Delay Adders for Fast Slew Rate on Column Pins (Part 1 of 2) -6 Speed Grade Standard Min
LVCMOS 2 mA 4 mA 8 mA 12 mA 3.3-V LVTTL 4 mA 8 mA 12 mA 16 mA 24 mA
-7 Speed Grade Min Max
0 - 563 - 984 - 1,142 0 - 400 - 987 - 942 - 1,142
-8 Speed Grade Unit Min Max
0 - 636 - 1,112 - 1,291 0 - 452 - 1,116 - 1,065 - 1,291 ps ps ps ps ps ps ps ps ps
Max
0 - 489 - 855 - 993 0 - 347 - 858 - 819 - 993
4-22 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-42. Cyclone I/O Standard Output Delay Adders for Fast Slew Rate on Column Pins (Part 2 of 2) -6 Speed Grade Standard Min
2.5-V LVTTL 2 mA 8 mA 12 mA 16 mA 1.8-V LVTTL 2 mA 8 mA 12 mA 1.5-V LVTTL 2 mA 4 mA 8 mA SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II LVDS
-7 Speed Grade Min Max
378 - 761 - 754 - 915 4 - 240 - 240 2,631 699 335 - 472 - 933 - 558 - 872 - 148 1,
-8 Speed Grade Unit Min Max
427 - 860 - 852 - 1034 5 - 271 - 271 2,974 790 379 - 533 - 1,055 - 631 - 986 - 1,298 ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps
Max
329 - 661 - 655 - 795 4 - 208 - 208 2,288 608 292 - 410 - 811 - 485 - 758 -9 98
Table 4-43. Cyclone I/O Standard Output Delay Adders for Fast Slew Rate on Row Pins (Part 1 of 2) -6 Speed Grade Standard Min
LVCMOS 2 mA 4 mA 8 mA 12 mA 3.3-V LVTTL 4 mA 8 mA 12 mA 16 mA 24 mA 2.5-V LVTTL 2 mA 8 mA 12 mA 16 mA 0 - 489 - 855 - 993 0 - 347 -858 - 819 - 993 329 - 661 - 655 - 795
-7 Speed Grade Min
0 - 563 - 984 - 1,142 0 - 400 - 987 - 942 - 1,142 378 - 761 - 754 - 915
-8 Speed Grade Unit Min
0 - 636 - 1,112 - 1,291 0 - 452 - 1,116 - 1,065 - 1,291 427 - 860 - 852 - 1,034
Max
Max
Max
ps ps ps ps ps ps ps ps ps ps ps ps ps
Altera Corporation January 2007
4-23 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-43. Cyclone I/O Standard Output Delay Adders for Fast Slew Rate on Row Pins (Part 2 of 2) -6 Speed Grade Standard Min
1.8-V LVTTL 2 mA 8 mA 12 mA 1.5-V LVTTL 2 mA 4 mA 8 mA 3.3-V PCI (1) SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II LVDS
-7 Speed Grade Min Max
1,483 4 - 240 2,631 699 335 - 1,009 - 472 - 933 - 558 - 872 - 1,148
-8 Speed Grade Unit Min Max
1,677 5 - 271 2,974 790 379 - 1,141 - 533 - 1,055 - 631 - 986 - 1,298 ps ps ps ps ps ps ps ps ps ps ps ps
Max
1,290 4 - 208 2,288 608 292 - 877 - 410 - 811 - 485 - 758 - 998
Table 4-44. Cyclone I/O Standard Output Delay Adders for Slow Slew Rate on Column Pins (Part 1 of 2) -6 Speed Grade I/O Standard Min
LVCMOS 2 mA 4 mA 8 mA 12 mA 3.3-V LVTTL 4 mA 8 mA 12 mA 16 mA 24 mA 2.5-V LVTTL 2 mA 8 mA 12 mA 16 mA 1.8-V LVTTL 2 mA 8 mA 12 mA
-7 Speed Grade Min Max
2,070 1,507 1,086 928 2,105 1,705 1,118 1,163 963 3,158 2,019 2,026 1,865 6,331 4,852 4,608
-8 Speed Grade Unit Min Max
2,340 1,704 1,228 1,049 2,380 1,928 1,264 1,315 1,089 3,570 2,283 2,291 2,109 7,157 5,485 5,209 ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps
Max
1,800 1,311 945 807 1,831 1,484 973 1,012 838 2,747 1,757 1,763 1,623 5,506 4,220 4,008
4-24 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-44. Cyclone I/O Standard Output Delay Adders for Slow Slew Rate on Column Pins (Part 2 of 2) -6 Speed Grade I/O Standard Min
1.5-V LVTTL 2 mA 4 mA 8 mA SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II LVDS
-7 Speed Grade Min Max
7,807 5,875 5,511 1,598 1,137 2,259 1,945 922
-8 Speed Grade Unit Min Max
8,825 6,641 6,230 1,807 1,285 2,554 2,199 1,042 ps ps ps ps ps ps ps ps
Max
6,789 5,109 4,793 1,390 989 1,965 1,692 802
Table 4-45. Cyclone I/O Standard Output Delay Adders for Slow Slew Rate on Row Pins (Part 1 of 2) -6 Speed Grade I/O Standard Min
LVCMOS 2 mA 4 mA 8 mA 12 mA 3.3-V LVTTL 4 mA 8 mA 12 mA 16 mA 24 mA 2.5-V LVTTL 2 mA 8 mA 12 mA 16 mA 1.8-V LVTTL 2 mA 8 mA 12 mA 1.5-V LVTTL 2 mA 4 mA 8 mA 3.3-V PCI
-7 Speed Grade Min Max
2,070 1,507 1,086 928 2,105 1,705 1,118 1,163 963 3,158 2,019 2,026 1,865 6,331 4,852 4,608 7,807 5,875 5,511 1,061
-8 Speed Grade Unit Min Max
2,340 1,704 1,228 1,049 2,380 1,928 1,264 1,315 1,089 3,570 2,283 2,291 2,109 7,157 5,485 5,209 8,825 6,641 6,230 1,199 ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps ps
Max
1,800 1,311 945 807 1,831 1,484 973 1,012 838 2,747 1,757 1,763 1,623 5,506 4,220 4,008 6,789 5,109 4,793 923
Altera Corporation January 2007
4-25 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-45. Cyclone I/O Standard Output Delay Adders for Slow Slew Rate on Row Pins (Part 2 of 2) -6 Speed Grade I/O Standard Min
SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II LVDS Note to Tables 4-40 through 4-45:
(1) EP1C3 devices do not support the PCI I/O standard.
-7 Speed Grade Min Max
1,598 1,137 2,259 1,945 922
-8 Speed Grade Unit Min Max
1,807 1,285 2,554 2,199 1,042 ps ps ps ps ps
Max
1,390 989 1,965 1,692 802
Tables 4-46 through 4-47 show the adder delays for the IOE programmable delays. These delays are controlled with the Quartus II software options listed in the Parameter column.
Table 4-46. Cyclone IOE Programmable Delays on Column Pins -6 Speed Grade Parameter
Decrease input delay to internal cells
-7 Speed Grade Min Max
178 2,543 3,034 3,515 178 0 3,515 0 634
-8 Speed Grade Unit Min Max
201 2,875 3,430 3,974 201 0 3,974 0 717 ps ps ps ps ps ps ps ps ps
Setting Min
Off Small Medium Large On
Max
155 2,122 2,639 3,057 155 0 3,057 0 552
Decrease input delay to input register Increase delay to output pin
Off On Off On
4-26 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-47. Cyclone IOE Programmable Delays on Row Pins -6 Speed Grade Parameter
Decrease input delay to internal cells
-7 Speed Grade Min Max
177 2,543 3,034 3,515 177 0 3,515 0 639
-8 Speed Grade Unit Min Max
200 2,875 3,430 3,974 200 0 3,974 0 722 ps ps ps ps ps ps ps ps ps
Setting Min
Off Small Medium Large On
Max
154 2,212 2,639 3,057 154 0 3,057 0 556
Decrease input delay to input Off register On Increase delay to output pin Off On Note to Table 4-47:
(1)
EPC1C3 devices do not support the PCI I/O standard
Maximum Input & Output Clock Rates
Tables 4-48 and 4-49 show the maximum input clock rate for column and row pins in Cyclone devices.
Table 4-48. Cyclone Maximum Input Clock Rate for Column Pins I/O Standard
LVTTL 2.5 V 1.8 V 1.5 V LVCMOS SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II LVDS
-6 Speed Grade
464 392 387 387 405 405 414 464 473 567
-7 Speed Grade
428 302 311 320 374 356 365 428 432 549
-8 Speed Grade
387 207 252 243 333 293 302 396 396 531
Unit
MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz
Altera Corporation January 2007
4-27 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-49. Cyclone Maximum Input Clock Rate for Row Pins I/O Standard
LVTTL 2.5 V 1.8 V 1.5 V LVCMOS SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II 3.3-V PCI (1) LVDS
(1)
-6 Speed Grade
464 392 387 387 405 405 414 464 473 464 567
-7 Speed Grade
428 302 311 320 374 356 365 428 432 428 549
-8 Speed Grade
387 207 252 243 333 293 302 396 396 387 531
Unit
MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz
Note to Tables 4-48 through 4-49:
EP1C3 devices do not support the PCI I/O standard. These parameters are only available on row I/O pins.
Tables 4-50 and 4-51 show the maximum output clock rate for column and row pins in Cyclone devices.
Table 4-50. Cyclone Maximum Output Clock Rate for Column Pins I/O Standard
LVTTL 2.5 V 1.8 V 1.5 V LVCMOS SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II LVDS Note to Table 4-50:
(1) EP1C3 devices do not support the PCI I/O standard.
-6 Speed Grade
304 220 213 166 304 100 100 134 134 320
-7 Speed Grade
304 220 213 166 304 100 100 134 134 320
-8 Speed Grade
304 220 213 166 304 100 100 134 134 275
Unit
MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz
4-28 Preliminary
Altera Corporation January 2007
Timing Model
Table 4-51. Cyclone Maximum Output Clock Rate for Row Pins I/O Standard
LVTTL 2.5 V 1.8 V 1.5 V LVCMOS SSTL-3 class I SSTL-3 class II SSTL-2 class I SSTL-2 class II 3.3-V PCI (1) LVDS
(1)
-6 Speed Grade
296 381 286 219 367 169 160 160 131 66 320
-7 Speed Grade
285 366 277 208 356 166 151 151 123 66 303
-8 Speed Grade
273 349 267 195 343 162 146 142 115 66 275
Unit
MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz
Note to Tables 4-50 through 4-51:
EP1C3 devices do not support the PCI I/O standard. These parameters are only available on row I/O pins.
PLL Timing
Table 4-52 describes the Cyclone FPGA PLL specifications.
Table 4-52. Cyclone PLL Specifications (Part 1 of 2) Symbol
fIN
Parameter
Input frequency (-6 speed grade) Input frequency (-7 speed grade) Input frequency (-8 speed grade)
Min
15.625 15.625 15.625 40.00
Max
464 428 387 60
Unit
MHz MHz MHz % ps MHz MHz MHz
fIN DUTY tIN JITTER fOUT_EXT (external PLL clock output)
Input clock duty cycle Input clock period jitter PLL output frequency (-6 speed grade) PLL output frequency (-7 speed grade) PLL output frequency (-8 speed grade)
200
15.625 15.625 15.625 320 320 275
Altera Corporation January 2007
4-29 Preliminary
Cyclone Device Handbook, Volume 1
Table 4-52. Cyclone PLL Specifications (Part 2 of 2) Symbol
fOUT (to global clock)
Parameter
PLL output frequency (-6 speed grade) PLL output frequency (-7 speed grade) PLL output frequency (-8 speed grade)
Min
15.625 15.625 15.625 45.00
Max
405 320 275 55 300 (2)
Unit
MHz MHz MHz % ps s MHz ns
tOUT DUTY tJITTER (1) tLOCK (3) fVCO N, G0, G1, E Notes to Table 4-52:
(1)
Duty cycle for external clock output (when set to 50%) Period jitter for external clock output Time required to lock from end of device configuration PLL internal VCO operating range Minimum areset time Counter values
10.00 500.00 10 1
100 1,000
32
integer
(2) (3)
The tJITTER specification for the PLL[2..1]_OUT pins are dependent on the I/O pins in its VCCIO bank, how many of them are switching outputs, how much they toggle, and whether or not they use programmable current strength or slow slew rate. fOUT 100 MHz. When the PLL external clock output frequency (fOUT) is smaller than 100 MHz, the jitter specification is 60 mUI. fIN/N must be greater than 200 MHz to ensure correct lock detect circuit operation below -20 C. Otherwise, the PLL operates with the specified parameters under the specified conditions.
4-30 Preliminary
Altera Corporation January 2007
Document Revision History
Document Revision History
Table 4-53 shows the revision history for this document.
Table 4-53. Document Revision History Date & Document Version
January 2007 v1.6

Changes Made
Added document revision history. Added new row for VCCA details in Table 4-1. Updated RCONF information in Table 4-3. Added new Note (12) on voltage overdrive information to Table 4-7 and Table 4-8. Updated Note (9) on RCONF information to Table 4-3. Updated information in "External I/O Delay Parameters" section. Updated speed grade information in Table 4-46 and Table 4-47.
Summary of Changes

Updated LVDS information in Table 4-51.
August 2005 v1.5 February 2005 v1.4
Minor updates.

Updated information on Undershoot voltage. Updated Table 4-2. Updated Table 4-3. Updated the undershoot voltage from 0.5 V to 2.0 V in Note 3 of Table 4-16. Updated Table 4-17. Added extended-temperature grade device information. Updated Table 4-2. Updated IC C 0 information in Table 4-3. Added clock tree information in Table 4-19. Finalized timing information for EP1C3 and EP1C12 devices. Updated timing information in Tables 4-25 through 4-26 and Tables 4-30 through 4-51. Updated PLL specifications in Table 4-52.
January 2004 v.1.3 October 2003 v.1.2

July 2003 v1.1
Updated timing information. Timing finalized for EP1C6 and EP1C20 devices. Updated performance information. Added PLL Timing section. Added document to Cyclone Device Handbook.
May 2003 v1.0
Altera Corporation January 2007
4-31 Preliminary
Cyclone Device Handbook, Volume 1
4-32 Preliminary
Altera Corporation January 2007
5. Reference & Ordering Information
C51005-1.3
Software
Cyclone(R) devices are supported by the Altera(R) Quartus(R) II design software, which provides a comprehensive environment for system-on-aprogrammable-chip (SOPC) design. The Quartus II software includes HDL and schematic design entry, compilation and logic synthesis, full simulation and advanced timing analysis, SignalTap(R) II logic analysis, and device configuration. Refer to the Design Software Selector Guide for more details on the Quartus II software features. The Quartus II software supports the Windows 2000/NT/98, Sun Solaris, Linux Red Hat v7.1 and HP-UX operating systems. It also supports seamless integration with industry-leading EDA tools through the NativeLink(R) interface.
Device Pin-Outs Ordering Information
Device pin-outs for Cyclone devices are available on the Altera web site (www.altera.com) and in the Cyclone FPGA Device Handbook. Figure 5-1 describes the ordering codes for Cyclone devices. For more information on a specific package, refer to Chapter 15, Package Information for Cyclone Devices.
Figure 5-1. Cyclone Device Packaging Ordering Information
EP1C Family Signature EP1C: Cyclone 20 F 400 C 7 ES Optional Suffix Indicates specific device options or shipment method. ES: Engineering sample
Device Type 3 4 6 12 20 Speed Grade 6, 7, or 8 , with 6 being the fastest
Operating Temperature Package Type T: Thin quad flat pack (TQFP) Q: Plastic quad flat pack (PQFP) F: FineLine BGA Pin Count Number of pins for a particular package C: Commercial temperature (tJ = 0 C to 85 C) I: Industrial temperature (tJ = -40 C to 100 C)
Altera Corporation January 2007
5-1 Preliminary
Cyclone Device Handbook, Volume 1
Document Revision History
Table 5-1 shows the revision history for this document.
Table 5-1. Document Revision History Date & Document Version
January 2007 v1.3 August 2005 v1.2 February 2005 v1.1 May 2003 v1.0
Changes Made
Added document revision history. Minor updates. Updated Figure 5-1. Added document to Cyclone Device Handbook.
Summary of Changes
5-2 Preliminary
Altera Corporation January 2007


▲Up To Search▲   

 
Price & Availability of EP1C12Q240I6ES

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X